UPG1-4-61-303-01 Sensata Technologies/Airpax, UPG1-4-61-303-01 Datasheet - Page 20

• Manufacturer Part Number: UPG1-4-61-303-01
• Description: MAGNETIC CIRC BRKR SP 30A TOG SW
• Manufacturer: Sensata Technologies/Airpax
• Series: UPGr

Specifications of UPG1-4-61-303-01

• Breaker Type: Hydraulic-Magnetic
• Voltage: 65VDC, 250VAC
• Current - Trip (it): 30A
• Number Of Poles: 1
• Actuator Type: Toggle
• Mounting Type: Panel Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q5003600

138
APG / UPG Decision Table - How to Order
The ordering code for APG/UPG circuit protectors may be
determined by following the steps in the decision tables
shown here.
The coding given permits a self-assigning part number but
with certain limitations. Units with mixed ratings,
combinations of styles, or constructions not listed in the
third decision table, require a factory-assigned part
number. with these, it is suggested that order entry be by
description and/or drawings, and a part number will be
established. Additionally, it is standard policy to establish a
factory-assigned part number whenever a descriptive
drawing exists to provide cross reference, traceability and
manufacturing control.
when specifying a circuit protector for AC motor start or
high inrush applications, the peak amplitude and surge
duration should be specified for factory assistance in
rating selection.
For example, the following is the code for a single pole
UPG, quick-connect type terminal series unit with auxiliary
switch, designed for operation in a 50/60Hz circuit. It has a
short time delay and a rating of 20 amperes. A white
handle is specified by the seventh decision table.
To determine the ordering number for your particular APG/
UPG unit, simply follow the steps shown. You may use this
number to place an order or as a reference for further
questions you may have.
Notes:
A It is recommended that power leads be soldered to protectors
B The standard current values for 100% of rated current are listed.
C UL recognized and CSA certified applications above 30 amperes
D Four pole protectors are available only in the APGH/UPGH and
E Sub panel mount available in APGX/UPGX configuration only.
F when “A” is specified in the sixth decision in conjunction with
G If a circuit breaker is marked in this manner, it means 277V per
having quick-connect terminals for current trip ratings above 10
amperes.
Please consult an Airpax office or sales representative for other
values.
are restricted to loads having a power factor of 75 minimum
and limited to 32Vdc only. Standard terminals on ratings over 30
amperes are 10-32 screw type.
APG/UPG types. The APGH/UPGH four pole provides one handle
per pole, while the APG/UPG four pole has handles in the center
two poles only, for simplified mounting.
APG/UPG-6 type, metric screw terminals are supplied.
pole – single phase source. Thus, if a two or three pole unit is
marked 277V, all line terminals must be connected to the same
phase, assuming the 277V is taken from line to neutral of 3 phase
277/480V system.
APG/UPG/IPG Series - APG/UPG Decision Tables
1
11
111
1111
Quick-
Connect
Terminals
2
1
Type
APG
UPG
APGX
UPGX
APGN
UPGN
APGH
UPGH
APGHX
UPGHX
Second Decision
Poles
Type
First Decision
(Note A)
Screw
Terminals
6
66
666
6666
Description
One handle per unit
One handle per unit
UL Recognized and
CSA Certified
One rocker handle per unit
One rocker handle per
unit UL Recognized and
CSA Certified
Panel seal
(one bat handle per unit)
Panel seal (one bat handle
per unit) UL Recognized and
CSA Certified
One handle per pole
One handle per pole
UL Recognized and
CSA Certified
One rocker handle per pole
One rocker handle per pole
UL Recognized and
CSA Certified
Number
Number
of poles
of poles
Single pole unit
Single pole unit
Two pole unit
Two pole unit
Three pole unit
Three pole unit
Four pole unit
Four pole unit
(Note D)
(Note D)
http://airpax.sensata.com/