17-P10-SI E-T-A, 17-P10-SI Datasheet

17-P10-SI

Manufacturer Part Number

17-P10-SI

Description

SOCKET W/BLADE TERMINALS

Manufacturer

E-T-A

Datasheet

1.17-P10-SI.pdf (5 pages)

Specifications of 17-P10-SI

Accessory Type

Socket, DIN Rail Mountable

For Use With/related Products

Circuit Breaker; E-1048-8I

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Other names

Q1837149B

Current page: 1 of 5
Download datasheet (302Kb)

The Smart Power Relay E-1048-8I.- is a remotely controllable electronic

load disconnecting relay with three functions in a single unit:

The 7 pin INLINE version is designed for use with various E-T-A

terminal blocks, e. g. 17-P10-Si. A choice of current ratings is available

from 1 A through 20 A. An operating voltage range of DC 9...32 V

allows the connection of DC 12 V and DC 24 V loads.

In order to switch and protect loads remotely, it has until now been

necessary to connect several discreet components together:

Now type E-1048-8I. combines all these functions in a single unit,

thus minimising the number of connections in the circuit and

thereby reducing the risk of failures.

Type E-1048-8I. is suited to all applications with DC 12 V or DC 24 V

circuits, where magnetic valves, motors or lamp loads have to be

switched, protected or monitored:

The Power Relay is also suitable for industrial use (process control,

machine-building, engineering) as an electronic coupling relay

between PLC and DC 12 V or DC 24 V load

●

Issue B

Description

Applications

Features

●

- an electro-mechanic relay, control cable and integral contact

- an additional protective element (circuit breaker or fuse) for

- a device for current measurement (shunt)

- road vehicles (utility vehicles, buses, special vehicles)

- rail vehicles

- marine industry (ships, boats, yachts etc.)

Integral power electronics provide a wear-resistant switching

function, insensitive to shock and vibration.

Only a fraction of the control power needed by electro-mechanical

relays is required for switching loads. This is important for battery

buffered load circuits which have to remain controlled even with

the generator off line.

The extremely low induced current consumption of less than 1 mA

is absolutely necessary for battery buffered applications.

The load circuit is disconnected in the event of an overload or

short circuit, the trip curve is also suitable for smaller motor loads.

The load circuit is permanently monitored for wire breakage.

Two status outputs for control signal AS and group signal SF

provide status indication. For processing the actual value of the

current flow in a power management system an analogue output

from 0 to 5 V is provided. This voltage signal may also be used as

an input to a control circuit or to switch off the unit by means of

external control in the event of low load current value.

For switching and monitoring loads of 20 A plus it is possible to

connect several units in parallel. Uniform power distribution between

units must be ensured by symmetrical design of the supply cables

(length and cross section).

Coloured label, e. g. red = 10 A, see ordering information.

to close the load circuit

cable or equipment protection

electronic relay

electronic overcurrent protection

status indication

Smart Power Relay E-1048-8I. (INLINE)

www.e-t-a.com

Power supply LINE +

Type

Voltage ratings U

Operating voltage U

Load circuit LOAD

Load output

Max. current rating I

Types of loads

Current rating range I

Induced current consumption

Typical voltage drop U

at rated current I

Switching point

Trip time

Current limitation

Temperature disconnection

After trip

Parallel connection of channels for loads of 20 A plus, several units of

Leakage current in OFF

condition

Free-wheeling diode

for connected load

Technical Data

of the unit (OFF condition) < 1 mA

(standard curve)

(at 25 °C) I

(T U = 25 °C, U S = DC 24 V) (T U = ambient temperature at U N )

E-1048-8I. INLINE

DC power supply with small R

battery and generator etc.

DC 12 V / DC 24 V

DC 9...32 V

Power MOSFET, high side switching

20 A

resistive, inductive, capacitive, lamp

loads, motors (depending on duration

of inrush current)

1 A...15 A (fixed ratings)

up to 85 °C ambient without load

reduction, 20 A up to 70 °C.

Two basic versions with factory pre-

set ratings:

version 1: 1 A / 2 A / 3 A / 5 A / 7.5 A / 10 A

version 2: 15 A / 20 A

1 A

2 A

3 A

5 A

typically 1.3 x I

(-40 °C...+85 °C: 1.1...1.5 x I

typically 200 ms with switch-on onto

overload and/or load increase on duty

version 1: typically 75 A

version 2: typically 350 A

power transistor > 150 °C

- resettable via external control signal

- reset of supply voltage

identical current ratings may be

connected in parallel. To ensure equal

distribution of current between units,

symmetrical design of the supply feed

is necessary (length and cross section).

version 1: max. 100 μA

version 2: max. 500 μA

integral

version 1: max. 40 A

version 2: max. 100 A

(low-high) at control input IN+

50 mV

55 mV

60 mV

80 mV

7.5 A

10 A

15 A

20 A

90 mV

110 mV

60 mV

)

6 - 23

Related parts for 17-P10-SI

17-P10-SI Summary of contents

Page 1

... The 7 pin INLINE version is designed for use with various E-T-A terminal blocks 17-P10-Si. A choice of current ratings is available from 1 A through operating voltage range of DC 9...32 V allows the connection and loads. In order to switch and protect loads remotely, it has until now been ...

Page 2

... EN 61000-6-2 Automotive directive: emitted interference, noise immunity: 72/245/EW6 und 95/54/E6 7 blade terminals 6 0 DIN 46244-A6.3-0.8 contact material CuZn37F37 copper-plated and tin-plated - E-T-A socket type 17-P10-Si (max. load board with 6.3 mm receptacles INLINE: 11 when plugged in 11 including terminals INLINE: Ultramid approx ...

Page 3

... AS SF yellow red control input 1…10 mA IN+ group fault signal max max control signal AS * analogue output 0 … max U( GND * Optionally available: - signal outputs analogue output U(I) E-1048-8I. 17-P10-Si LINE + (2) (2) [2(k)] GND (5) (5) [12] SF (7) (7) [24] U(I) (3) (3) [2(i)] AS (6) (6) [23] IN+ (4) ...

Page 4

... Smart Power Relay E-1048-8I. (INLINE) Typical time/current characteristics (T Version 7.5 A and 10 A (standard 200 ms) 1000 100 10 1 current limitation 0 typ. 1 ... times rated current I Version and 20 A (standard 200 ms) 1000 100 current limitation 0 typ. 1 ... times rated current ° (A) (typ (A) (typ. 350 A) N www.e-t-a.com Issue B ...

Page 5

... E-1048-8I. - Single mounting sockets (with adapter) ( max. load) 17-P10-Si 17-P10-Si-20025 17-P70-Si 17-P70-Si-20025 (retaining clip Y 300 581 11 available on request) polarized blade terminal blade terminal DIN 46244 part 2 DIN 46244-A6.3-0.8 (QC .250) C profile (2xA2.8-0.8) (QC 2x.110) -P10 slot for fitting labels from 6.3 Phoenix, Weidmüller ...

Related keywords

17-p10-si
17-P10-SI datasheet
17-P10-SI data sheet
17-P10-SI pdf datasheet
17-P10-SI component
17-P10-SI part
17-P10-SI distributor
17-P10-SI RoHS
17-P10-SI datasheet download