PQ015EZ01 Sharp, PQ015EZ01 Datasheet
PQ015EZ01
Available stocks
Related parts for PQ015EZ01
PQ015EZ01 Summary of contents
Page 1
... Space equipment * Nuclear power control equipment [ (4) Please contact and consult with a Sharp sales representative if there are any questions regarding interpretation of the above three paragraphs. 3. Please contact and consult with a Sharp sales representative for any questions about this product. CUSTOMER’S APPROVAL DATE BY ...
Page 2
... SHARP CORPORATION 1. AppIication This specification appkes to the outbne tape packing type series regulator AppIied Model name PQO15EZOlZZ. PQO15EZOlZP. usage PQ++*EZOlZ are the device for stabikzation with built-in ON/OFF protection function These devices are possible Block diagram DC input 0 2. Outline : Refer to the attached 3 ...
Page 3
SHRRP CORPORATION : Refer to the attached 6. Supplement 6.1 Example of application 6.2 Taping and reel packaging 6.3 Sleeve packaging 6.4 ODS materials This product shall not contain Also, the following for this product. Materials for ODS 6.5 Brominated ...
Page 4
... SHARP CORPORATlON 2. Outline 6.6 i’4AX . 52~0 Applied I model No. PQO15EZOlZZ PQ018E20122 WO25EzO1ZZ V~ t W030EZOlZZ 1 P6033EZOlZZ t Pii015E20127 PQ018EzOIzz PQ025EZO 1 ZZ PQO3OEzO 1ZZ 172 . PQC----- x33E7fi _-- % (Example of the marking ;,!. _.” -#I Model No Lot No. /(DIN standard) 1 Marked I I model No. I 015EZO1 018EzOl 025EZO 1 1 030E: ...
Page 5
... SHARP CORPORflTION 3. Ratings and characteristics 3.1 Absolute maximum ratings Parameter Input voltage (‘1) Output control voltage (‘1) Output current Power dissipation (*2) Junction temperature Operating temperature Storage temperature Soldering temperature (+l) All are open except GND and applicable (* With infinite (*3) There is case that over heat protection ...
Page 6
SHRRP CORPORATION 3.2 EIectrlcal characteristics Unless otherwise specified condition shall be Wn=Vo(TYP)+lV. Io=O.SmA. Vc=2.7V. Ta=25’c Parameter Input voltage Output voltage Load regulation Line regulation Temperature coefacient of output voltage Ripple rejection Dropout voltage On-state voltage for control On-state current for ...
Page 7
SHflRP CORPORATION 3.3 Electrical characteristics Fig. 2 Standard measuring Fig. 3 Standard measuring f=lZOHz sine wave ei(rms)=0.5V vin=vo(TYFq+ 1v 10=0.3A RR=20 log (ei(rms)/eo(rmsll measuring circuit circuit of Regulator portion circuit of critkal rate of ripple rejection ...
Page 8
SHflRP CORPORfiTION Power dissipation Size: 5OX50X1.6mm Thickness of copper : 3 rating (Typical value Ambient temperature Ta (C) Mounting PCB I I =-T Material : Glass-cloth epoxy resin ...
Page 9
SHfiRP CORPOMTION The reliability of products shall satisfy items listed below. Test Items Temperature cycung Humidity (Steady State) Damp Heat cyclic High temp. storage Low temp. storage Operation life Mechanical shock Vibration [variable frequency) Electrostatic discharge Soldering heat Robustness of ...
Page 10
SHRRP CORPORfllION l 1 Soldering area is shown below. / Terminal bending is shown below. c ’ i ’ Weight 5. Outgoing inspecti on TABLE II-A single sampling The AQL according to the inspection Defect ...
Page 11
SHflRP CORPORATION 6. Supplement 6.1 Example of application \ CO High : Output ON-OFF s@nal or Open : Output i T’ OFF I ...
Page 12
... SHARP CORPORflTION 6.2 Packing specifications 6.2.1 Packing conditions ( 1) Tape structure and Dimensions The tape shall have a structure pressed on the carrier static electricity. (2) Reel structure and Dimensions The reel shall be made of polystyrene. (3) Direction of product Product direction the hole side on the tape. 6.2.2 Tape characteristics (1) Adhesiveness ...
Page 13
... SHARP CORPORflTION 6.2.4 Indication (1) -1 The reel shall be pasted label with following Model No (2) Package case The outer packaging Model No 6.2.5 Storage condition Taped products and the humidities longer than for lodays, 6.2.6 Others (1) joint of tape The cover tape and carrier (2) The way to repair taped failure ...
Page 14
... SHARP CORPORflTION Fig. B Reel structure and Dimensions Fig. C Direction of product insertion Pull-out direction Dimensions : TYP. value Unit : ...
Page 15
... SHARP CORPORRTION 6.3 Sleeve packaging (PQ’+*Eu)lZ) 6.3.1 Packing conditions (1) Sleeve structure The sleeve shall be made of high inpuct (Plastics with preventing Dimensions are shown Fig. D. (2) The packfng case shall be made of corrugated Dimensions are shown Fig. F. (3) Stopper structure The stopper shall be made of styrene butadiene 6 ...
Page 16
SHHHY CUHPUHHI IUN Fig. D @See ye @Stopper (With pulled portion) Fig sleeves ():Typ. unit: Mass per packaged Inspection date GKtnnnor w”.“~~r. (Without pulled potion IineX 4 stairs) mm 1.6kg TYP case: ...
Page 17
... SHARP CORPORfiTION 7. Notes 7.1 External connection (1) Please perform shortest individual terminal. of capacitor and capacity. output voltage on your use mounting (2) The input terminal and direct driving also available. In case that ON/OFF to connect the ON/OFF (3) As voltage application reversely, may occur the degradation please avoid it absolutely. ...
Page 18
... SHARP CORPORATION 7.3 Static electricity Good caution must be exercised consists of a bipolar against excessive voltages (al frytibody must be grounded . (b) Anything that is in contact with the device such as workbench, inserter, or measuring (cl Use a solder dip basin with a minimum resistance 10MQ or more] from the commercial Also the solder dip basin must be grounded. ...
Page 19
... SHARP CORPORATION (2) Dip soldering We recommend that solder dip should be 260F and 1 time only. Please obey the note items below concerning (a) Atter solder dip, please do cooling naturally. (b) Please shall not give the mechanical In advance, please confirm in order to avoid any soldering (3) Hand soldering ...