MAX919 Maxim, MAX919 Datasheet
MAX919
Available stocks
Related parts for MAX919
MAX919 Summary of contents
Page 1
... Rails™ inputs and are guaranteed to operate down to +1.8V. The MAX917/MAX918 feature an on-board 1.245V ±1.5% reference and draw an ultra-low supply current of only 750nA, while the MAX919/MAX920 (with- out reference) require just 380nA of supply current. These features make the MAX917–MAX920 family of comparators ideal for all 2-cell battery applications, including monitoring/management ...
Page 2
... EE Voltage Inputs (IN+, IN-, REF) .........(V EE Current Into Input Pins......................................................±20mA Output Voltage MAX917/MAX919 ........................(V EE MAX918/MAX920 ......................................(V Output Current..................................................................±50mA Output Short-Circuit Duration .............................................10sec Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied ...
Page 3
... Reference Voltage Temperature TC Coefficient Reference Output e Voltage Noise ΔV Reference Line Regulation ΔV ΔV Reference Load Regulation ΔI OUT ELECTRICAL CHARACTERISTICS—MAX919/MAX920 (V = + -40°C to +85°C, unless otherwise noted. Typical values are PARAMETER SYMBOL Supply Voltage Range ...
Page 4
... 1.8V CC MAX919 only 1. PULLUP MAX920 only PULLUP MAX919 only 15pF 15pF L = +25°C. Specification limits over temperature ( 100mV, and load capacitance of C OVERDRIVE = +25°C.) (Note 1) A MIN TYP MAX 10 0.1 1 0.5 3 190 400 ...
Page 5
... TEMPERATURE (°C) MAX919/MAX920 SUPPLY CURRENT vs. OUTPUT TRANSITION FREQUENCY 1. 100 1k 10k 100k OUTPUT TRANSITION FREQUENCY (Hz) MAX917/MAX919 OUTPUT-VOLTAGE HIGH vs. SOURCE CURRENT 0 1. 0.4 0.3 0.2 0 SOURCE CURRENT (mA) 5 ...
Page 6
... REFERENCE SOURCE CURRENT 1.2440 1.2435 V = 1.8V CC 1.2430 1.2425 CC 1.2420 1.2415 SOURCE CURRENT (nA) MAX917/MAX919 SHORT-CIRCUIT SOURCE CURRENT vs. TEMPERATURE 140 120 100 1. -40 - TEMPERATURE (°C) MAX917/MAX918 REFERENCE VOLTAGE vs. TEMPERATURE 1 ...
Page 7
... 100 1k 10k R (kΩ) PULLUP PROPAGATION DELAY (t ) vs. CAPACITIVE LOAD 120 100 0.01 0 CAPACITIVE LOAD (nF) MAX917/MAX919 ) PROPAGATION DELAY (t vs. INPUT OVERDRIVE 100 INPUT OVERDRIVE (mV) ) vs. PROPAGATION DELAY (t ...
Page 8
... MAX917-920 toc34 IN+ (50mV/div) OUT (2V/div) MAX917/MAX919 PROPAGATION DELAY ( 3V) CC MAX917-920 toc30 IN+ (50mV/ div) OUT (2V/div) 20μs/div MAX917/MAX919 10kHz RESPONSE (V = 1.8V) CC MAX917-920 toc33 IN+ (50mV/ div) OUT (1V/div) 20μs/div POWER-UP/DOWN RESPONSE MAX917-920 toc35 V CC (2V/div) OUT (2V/div) 40μs/div ...
Page 9
... Large internal output drivers allow rail-to-rail output swing with up to ±8mA loads. The output stage employs a unique design that mini- mizes supply-current surges while switching, virtually eliminating the supply glitches typical of many other comparators. The MAX917/MAX919 have a push-pull _______________________________________________________________________________________ IN+ OUT IN- ...
Page 10
... AA SIZE (V) (V) (mA-h) 3.0 1.8 2000 2.4 1.8 750 3.5 2.7 1000 2.4 1.8 1000 V CC 120nA REF V EE Internal Hysteresis ) and one for the THR ) (Figure 2). The difference THF ). When HB MAX917/MAX918 MAX919/MAX920 OPERATING TIME OPERATING TIME (hr) (hr 2 937,500 6 1.875 ...
Page 11
... HB V THF OUT Figure 2. Threshold Hysteresis Band Additional Hysteresis (MAX917/MAX919) The MAX917/MAX919 have a 4mV internal hysteresis band (V ). Additional hysteresis can be generated HB with three resistors using positive feedback (Figure 3). Unfortunately, this method also slows hysteresis re- sponse time. Use the following procedure to calculate resistor values ...
Page 12
... Figure 5 shows a zero-crossing detector application. ⎛ ⎞ ⎜ ⎟ The MAX919’s inverting input is connected to ground, ⎝ ⎠ and its noninverting input is connected to a 100mV signal source. As the signal at the noninverting input crosses 0V, the comparator’s output changes state. ⎞ ...
Page 13
... Comparators With/Without Reference For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 14
... Comparators With/Without Reference For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 15
... Added lead-free and automotive qualified parts Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 15 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...