max5742 Maxim Integrated Products, Inc., max5742 Datasheet

no-image

max5742

Manufacturer Part Number
max5742
Description
Max5742 12-bit, Low-power, Quad, Voltage-output Dac With Serial Interface
Manufacturer
Maxim Integrated Products, Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
max5742AUB
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
max5742EUB
Manufacturer:
INF
Quantity:
3 131
Part Number:
max5742EUB
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
max5742EUB+T
Manufacturer:
PEREGRIN
Quantity:
12 000
The MAX5742 quad, 12-bit, low-power, buffered volt-
age-output, digital-to-analog converter (DAC) is pack-
aged in a space-saving 10-pin µMAX package (5mm
3mm). The wide supply voltage range of +2.7V to
+5.5V and 229µA supply current accommodates low-
power and low-voltage applications. DAC outputs
employ on-chip precision output amplifiers that swing
Rail-to-Rail
voltage range from 0 to V
ence input is high impedance, further reducing the sys-
tem’s total power consumption.
The 20MHz, 3-wire SPI™, QSPI™, MICROWIRE™ and
DSP-compatible serial interface saves board space
and reduces the complexity of opto- and transformer-
isolated applications. The MAX5742 on-chip power-on
reset (POR) circuit resets the DAC outputs to zero and
loads the output with a 100k
provides additional safety for applications that drive
valves or other transducers that need to be off on
power-up. The MAX5742’s software-controlled power-
down reduces supply current to less than 0.3µA and
provides software-selectable output loads (1k , 100k ,
or high impedance) while in power-down. The MAX5742
is specified over the -40°C to +125°C automotive tem-
perature range.
19-2122; Rev 2; 7/03
Functional Diagram appears at end of data sheet.
Rail-to-Rail is a registered trademark of Nippon Motorola, Inc.
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor, Corp.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Automatic Tuning
Gain and Offset Adjustment
Power Amplifier Control
Process Control I/O Boards
Battery-Powered Instruments
VCO Control
®
. The MAX5742’s reference input accepts a
12-Bit, Low-Power, Quad, Voltage-Output
________________________________________________________________ Maxim Integrated Products
General Description
DD
. In power-down the refer-
resistor to ground. This
Applications
DAC with Serial Interface
o Ultra-Low Power Consumption
o Wide +2.7V to +5.5V Single-Supply Range
o 10-Pin µMAX Package
o 0.3µA Power-Down Current
o Guaranteed 12-Bit Monotonicity (±1LSB DNL)
o Safe Power-Up Reset to Zero Volts at DAC Output
o Three Software-Selectable Power-Down
o Fast 20MHz 3-Wire SPI, QSPI, and MICROWIRE-
o Rail-to-Rail Output Buffer Amplifiers
o Schmitt-Triggered Logic Inputs for Direct
o Wide -40°C to +125°C Operating Temperature
MAX5742EUB
MAX5742AUB
Impedances (100k , 1k , Hi-Z)
Compatible Serial Interface
Interfacing to Optocouplers
Range
TOP VIEW
PART
229µA at V
271µA at V
SCLK
GND
V
DIN
CS
DD
DD
DD
-40°C to +125°C
1
2
3
4
5
-40°C to +85°C
TEMP RANGE
= +3.6V
= +5.5V
Ordering Information
MAX5742
MAX
Pin Configuration
10
9
8
7
6
OUTD
OUTC
OUTB
OUTA
REF
10 µMAX
10 µMAX
PIN-PACKAGE
Features
1

Related parts for max5742

max5742 Summary of contents

Page 1

... The MAX5742’s software-controlled power- down reduces supply current to less than 0.3µA and provides software-selectable output loads (1k , 100k , or high impedance) while in power-down. The MAX5742 is specified over the -40°C to +125°C automotive tem- perature range. Automatic Tuning ...

Page 2

Low-Power, Quad, Voltage-Output DAC with Serial Interface ABSOLUTE MAXIMUM RATINGS V to GND ..............................................................-0.3V to +6V DD OUT_, SCLK, DIN, CS, REF to GND...............-0 Maximum Continuous Current Into Any Pin......................±50mA Continuous Power Dissipation (T = +70°C) A ...

Page 3

Low-Power, Quad, Voltage-Output ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V, GND = REF V = +5V +25°C PARAMETER SYMBOL DIGITAL INPUTS (SCLK, DIN, CS) Input High Voltage Input Low Voltage Input ...

Page 4

Low-Power, Quad, Voltage-Output DAC with Serial Interface __________________________________________Typical Operating Characteristics ( +25°C, unless otherwise noted.) REF DD A INTEGRAL NONLINEARITY vs. CODE + +5V DD ...

Page 5

Low-Power, Quad, Voltage-Output ( +25°C, unless otherwise noted.) REF DD A WORST-CASE INL AND DNL vs. TEMPERATURE MAXIMUM INL MAXIMUM DNL MINIMUM DNL -8 MINIMUM INL -12 -16 ...

Page 6

... DIGITAL-TO-ANALOG GLITCH IMPULSE MAX5742 toc21 V , SCLK 5V/div V OUT_ CODE 800 HEX 1V/div (V = +5V) DD MAX5742 toc18 V , SCLK 5V/div V OUT_ 1V/div 1 s/div (V = +3V) DD MAX5742 toc20 V , SCLK 5V/div V OUT_ 1V/div CODE C00 TO 400 HEX 200pF L 1 s/div (V = +5V) DD MAX5742 toc22 SCLK 500kHz SCLK 2V/div ...

Page 7

... TIME = OUT_ AC-COUPLED, 2mV/div (V = +5V) DD MAX5742 toc24 SCLK 500kHz SCLK 2V/div V OUT_ AC-COUPLED, 20mV/div CODE 800 HEX to 7FF HEX 1 s/div (V = +5V) DD MAX5742 toc26 V DD 2V/div V OUT_ AC-COUPLED, 10mV/div V RISE DD TIME = s/div (V = +3V) DD MAX5742 toc28 V DD 2V/div V RISE DD TIME = ...

Page 8

... CLOCK FEEDTHROUGH (V = +5V) DD MAX5742 toc30 SCLK, 2V/div V OUT_ AC-COUPLED, CODE = 800 HEX, 1mV/div 2 s/div f = 50kHz SCLK 2 s/div (V = +5V) DD MAX5742 toc32 V DD, AC-COUPLED, 100mV/div V OUT_ AC-COUPLED, 10mV/div 20 s/div = +5V) DD MAX5742 toc34 CODE FFF HEX V OUTA, to 00B HEX 2V/div V OUTB, AC-COUPLED, 2mV/div ...

Page 9

... This extra time is needed to allow the internal bias to wake-up. Power-down mode reduces current consumption to 0.3µA. . The output DD The MAX5742 digital interface is a standard 3-wire con- nection compatible with SPI/QSPI/MICROWIRE/DSP interfaces. The chip-select input (CS) frames the serial 12 data loading at DIN. Immediately following CS high-to- ...

Page 10

... DAC A-D Power-On Reset (POR) The MAX5742 has an internal POR circuit. At power-up all DACs are powered-down and OUT_ is terminated to GND through 100k resistors. Contents of input and DAC registers are cleared to all zero. An 8µs recovery time after issuing a wake-up command is needed before writ- ing to the DAC registers ...

Page 11

... MAX5742 configured for a unipolar output, where the output voltages and the reference inputs have the same polarity. Table 3 lists the unipolar output codes. The MAX5742 can be configured for bipolar operation using a dual supply op amp (Figure 4). The transfer function for bipolar operation is: ...

Page 12

... Input registers transparent, data shifted directly to DAC registers, OUTA–OUTD A–D updated A–D Data shifted to input registers, OUTA–OUTD unchanged A–D Shift data from input registers to DAC registers, OUTA–OUTD updated REF V DD DAC_ OUT_ MAX5742 Figure 4. Bipolar Output Circuit FUNCTION +2.7V TO +5. OUT_ V- MAX5742 OUT ...

Page 13

Low-Power, Quad, Voltage-Output Table 3. Unipolar Code Table DAC CONTENTS ANALOG OUTPUT 1111 1111 1111 1000 0000 0001 1000 0000 0000 0111 1111 1111 0000 0000 0001 0000 0000 0000 Chip Information TRANSISTOR COUNT: 14,458 PROCESS: BiCMOS ______________________________________________________________________________________ DAC ...

Page 14

... LOGIC AND SHIFT REGISTER CS SCLK DIN 14 ______________________________________________________________________________________ REF OUTPUT 12-BIT DAC A BUFFER OUTPUT 12-BIT DAC B BUFFER OUTPUT 12-BIT DAC C BUFFER OUTPUT 12-BIT DAC D BUFFER POWER-DOWN CONTROL LOGIC MAX5742 GND Functional Diagram OUTA RESISTOR NETWORK OUTB RESISTOR NETWORK OUTC RESISTOR NETWORK OUTD RESISTOR NETWORK ...

Page 15

Low-Power, Quad, Voltage-Output (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages ÿ 0.50±0.1 0.6±0.1 1 0.6±0.1 TOP VIEW ...

Related keywords