LT1466 LINER [Linear Technology], LT1466 Datasheet
LT1466
Available stocks
Related parts for LT1466
LT1466 Summary of contents
Page 1
... As can be seen, the LT1466L/LT1467L’s limits are much tighter for inputs near either supply. The LT1466L is available in 8-lead PDIP and SO-8 pack- ages with the standard dual pinout. The LT1467L features the standard quad pinout and is available in a 16-lead narrow SO package ...
Page 2
... U RATINGS Junction Temperature ........................................... 150 C Storage Temperature Range ................. – 150 C Lead Temperature (Soldering, 10 sec).................. 300 ORDER PART NUMBER OUT A 1 – LT1466LCN8 LT1466LCS8 + – PART MARKING OUT 1466L 16-LEAD PLASTIC SO T JMAX = V = half supply, unless otherwise noted ...
Page 3
... 2.3V to 12V 0. 2.3V to 12V 0.5V (Note Load I = 0.5mA SINK I = 2.5mA SINK No Load I = 0.5mA SOURCE I = 2.5mA SOURCE LT1466L/LT1467L MIN TYP MAX UNITS 105 84 105 32 60 135 270 235 470 + + V – 0.052 V – 0.026 + + V – 0.270 V – ...
Page 4
... LT1466L/LT1467L ELECTRICAL CHARACTERISTICS 5V 0V, unless otherwise noted SYMBOL PARAMETER V Input Offset Voltage OS V Input Offset Voltage Shift OS Input Offset Voltage Match (Channel-to-Channel) I Input Bias Current B I Input Bias Current Shift B I Input Offset Current OS I Input Offset Current Shift ...
Page 5
... 5V 1900 AMPLIFIERS – 400 – 300 – 200 –100 0 100 200 300 INPUT OFFSET VOLTAGE ( V) 1466L/67L G02 LT1466L/LT1467L MIN TYP MAX – – 0.042 V + 0.080 – – 0.150 V + 0.300 – – 0.270 V + 0.540 + + V – ...
Page 6
... LT1466L/LT1467L W U TYPICAL PERFORMANCE CHARACTERISTICS Supply Current vs Temperature 5V – 40 – 100 TEMPERATURE ( C) 1466L/67L G04 Output Saturation Voltage vs Load Current (Output Low) 1000 100 T = – ...
Page 7
... 2.5V S – 5 –10 –15 – 100 120 140 160 TIME AFTER POWER-UP (SEC) LT1466L/LT1467L Power Supply Rejection Ratio vs Frequency 2. 2. POSITIVE 40 SUPPLY 30 20 NEGATIVE SUPPLY 10 0 1000 1 10 FREQUENCY (kHz) 1466L/67L G14 ...
Page 8
... U APPLICATIONS INFORMATION Rail-to-Rail Operation The LT1466L/LT1467L differ from conventional op amps in the design of both the input and output stages. Figure 1 shows a simplified schematic. The input stage consists of two differential amplifiers, a PNP stage Q1-Q2 and an NPN stage Q3-Q4, that are active over different portions of the input common mode range ...
Page 9
... When the amplifier switches between stages, the offset voltage may go up, down or remain flat. Both stages of the LT1466L/LT1467L are trimmed; one at the negative sup ply and the other at the positive supply. The resulting common mode rejection ratio of 83dB minimum is much better than typical rail-to-rail amplifiers ...
Page 10
... LT1466L/LT1467L PACKAGE DESCRIPTION 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.025 0.325 –0.015 +0.635 8.255 –0.381 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 0.010 – 0.020 45 (0.254 – ...
Page 11
... Plastic Small Outline (Narrow 0.150) (LTC DWG # 05-08-1610 0.228 – 0.244 (5.791 – 6.197 0.053 – 0.069 (1.346 – 1.752) 0.014 – 0.019 (0.355 – 0.483) LT1466L/LT1467L 0.386 – 0.394* (9.804 – 10.008 0.150 – 0.157** (3.810 – 3.988 0.004 – ...
Page 12
... LT1466L/LT1467L U TYPICAL APPLICATIONS 4-Pole,1kHz, 3.3V Single Supply State Variable Filter Using the LT1467L C1 10,000pF R1* 29.5k – 1/4 LT1467L + 10k 3.3V 10k *1% RESISTORS RELATED PARTS PART NUMBER DESCRIPTION ® LTC 1152 Rail-to-Rail Input and Output, Zero-Drift Op Amp LT1366/LT1367 Dual/Quad Precision, Rail-to-Rail Input and Output ...