adg3245 Analog Devices, Inc., adg3245 Datasheet
adg3245
Available stocks
Related parts for adg3245
adg3245 Summary of contents
Page 1
... Hot Plug Analog Switch Applications GENERAL DESCRIPTION The ADG3245 3.3 V, 8-bit, 2-port digital switch designed on Analog Devices’ low voltage CMOS process, which provides low power dissipation yet gives high switching speed and very low on resistance, allowing inputs to be connected to outputs without additional propagation delay or generating additional ground bounce noise ...
Page 2
... ADG3245–SPECIFICATIONS Parameter DC ELECTRICAL CHARACTERISTICS Input High Voltage Input Low Voltage Input Leakage Current OFF State Leakage Current ON State Leakage Current Maximum Pass Voltage 3 CAPACITANCE A Port Off Capacitance B Port Off Capacitance A, B Port On Capacitance Control Input Capacitance 3 SWITCHING CHARACTERISTICS 4 Propagation Delay ...
Page 3
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADG3245 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 4
... ADG3245 V Positive Power Supply Voltage. CC GND Ground (0 V) Reference. V Minimum Input Voltage for Logic 1. INH V Maximum Input Voltage for Logic 0. INL I Input Leakage Current at the Control Inputs OFF State Leakage Current the maximum leakage current at the switch pin in the OFF state. ...
Page 5
... Voltage for Different Temperatures 2 2.7V CC SEL = – 1 2. 2.3V CC 1.0 0 0.5 1.0 1.5 2.0 2.5 3.0 V – TPC 7. Pass Voltage vs REV. 0 Typical Performance Characteristics–ADG3245 2. SEL = 2. 2. 0.5 1.0 1.5 2.0 2.5 3 – TPC 2. On Resistance vs. ...
Page 6
... ADG3245 3 2 2.0 = 3.3V; SEL = 1.5 = SEL = 3. 1.0 0.5 = SEL = 2. 0.02 0.04 0.06 0.08 0.10 I – TPC 10. Output Low Characteristic – 3.3V/2.5V CC SEL = V CC – 0dBm IN N/W ANALYZER : – –8 –10 –12 –14 0.03 0 100 1000 FREQUENCY – MHz TPC 13. Bandwidth vs. Frequency 3 ...
Page 7
... TPC 22. Jitter @ 1.244 Gbps, PRBS 31 REV 3.3V 20dB CC 35mV/DIV SEL = 3.3V ATTENUATION 100ps/DIV p TPC 20. Eye Pattern; 1.244 Gbps 3.3 V, PRBS 31 CC –7– ADG3245 V = 2.5V 20dB CC 37mV/DIV SEL = 2.5V ATTENUATION 200ps/DIV p TPC 21. Eye Pattern; 1 Gbps 2.5 V, PRBS 31 CC ...
Page 8
... ADG3245 For the following load circuit and waveforms, the notation that is used OUT PULSE D.U.T. GENERATOR R T NOTES t PULSE GENERATOR FOR ALL PULSES: 2.5ns, R FREQUENCY 10MHz. C INCLUDES BOARD, STRAY, AND LOAD CAPACITANCES . THE TERMINATION RESISTOR, SHOULD BE EQUAL THE PULSE GENERATOR ...
Page 9
... MICROPROCESSOR Figure 8. 2 1.8 V Voltage Translation, SEL = V supply 1.8 V Translation The ADG3245 offers the option of interfacing between a 3.3 V device and a 1.8 V device. This is possible through use of the SEL pin. 2.5V SEL pin: An active low control pin. SEL activates internal circuitry in the ADG3245 that allows voltage translation between 3 ...
Page 10
... Figure 11. Location of Bus Switched in a Bus Isolation Application Hot Plug and Hot Swap Isolation The ADG3245 is suitable for hot swap and hot plug applications. The output signal of the ADG3245 is limited to a voltage that is below the V supply, as shown in Figures 6, 8, and 10. Therefore CC the switch acts like a buffer to take the impact from hot insertion, protecting vital and expensive chipsets from damage ...
Page 11
... Dimensions shown in millimeters 4.0 BSC SQ 0.60 MAX TOP 3.75 VIEW BSC SQ 0.75 0.55 0.35 0.80 MAX 12 MAX 0.65 NOM 0.05 0.02 0.00 COPLANARITY 0.50 0.20 0.08 REF BSC COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1 (RU-20) Dimensions shown in millimeters 6.60 6.50 6. 4.50 4.40 4.30 6.40 BSC 1 10 PIN 1 0.65 1.20 BSC MAX 0.20 0.09 0.30 SEATING 0.19 PLANE COMPLIANT TO JEDEC STANDARDS MO-153AC –11– ADG3245 0.60 MAX 2.25 BOTTOM 2.10 SQ VIEW 1. 0.30 0.23 0.18 0.75 8 0.60 0 0.45 ...
Page 12
–12– ...