G2R-14-DC5 Omron, G2R-14-DC5 Datasheet - Page 25
![RELAY PC MNT PWR SPDT 10A 5VDC](/photos/9/41/94195/g2r-14_pwr_relay_sml.jpg)
G2R-14-DC5
Manufacturer Part Number
G2R-14-DC5
Description
RELAY PC MNT PWR SPDT 10A 5VDC
Manufacturer
Omron
Series
G2Rr
Datasheets
1.G2R-1A-E-DC12.pdf
(14 pages)
2.G2R-1A-E-DC12.pdf
(30 pages)
3.G2R-2-SND_DC24S.pdf
(19 pages)
4.G2R-1AE-DC24.pdf
(15 pages)
Specifications of G2R-14-DC5
Relay Type
General Purpose
Coil Resistance
47 Ohms
Contact Form
SPDT (1 Form C)
Contact Rating (current)
10A
Switching Voltage
380VAC, 125VDC - Max
Coil Type
Standard
Coil Current
106mA
Coil Voltage
5VDC
Turn On Voltage (max)
3.5 VDC
Turn Off Voltage (min)
0.75 VDC
Mounting Type
Through Hole
Termination Style
PC Pin
Circuit
SPDT (1 Form C)
Contact Rating @ Voltage
10A @ 250VAC
Control On Voltage (max)
3.5 VDC
Control Off Voltage (min)
0.75 VDC
Contact Rating
10 A
Contact Termination
Solder Pin
Mounting Style
Through Hole
Power Consumption
530 mW
Contact Material
Silver Alloy
Coil Voltage Vdc Nom
5V
Contact Current Max
10A
Contact Voltage Ac Nom
250V
Contact Voltage Dc Nom
30V
Contact Configuration
SPDT
Current, Rating
10 A
Function
Power
Number Of Pins
5
Power, Rating
2500⁄300 VA⁄W
Standards
UL, CSA, VDE, CE
Termination
Through Hole
Voltage, Control
5 VDC
Voltage, Rating
380 VAC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
G2R-114P-V-US-DC5
G2R14DC5
Z743
G2R14DC5
Z743
■ Designing Power Circuit
Since many documents and reference books on the power circuit are
available, a detailed description is omitted here.
■ Connection of Surge
Note: This graph is plotted by measuring the surge voltage in the line
When connecting a surge suppressor, pay attention to the following
points:
1. Place the surge suppressor near the device to be protected. For
External surge
* In the circuit above, varistors B
** Resistor R protects diode bridge D from the inrush current
*** C
example, to protect a device from external surge, set the surge
suppressor at the inlet of the device’s power cable.
To suppress an internal surge, the suppressor must be placed
near the surge generating source.
Suppressor
power circuit elements, as well as elements related to the
power circuit, in case the voltage on the power line experi-
ences surges (due to lightning or the surge voltage gener-
ated in other devices connected to the power circuit).
Connect an appropriate surge suppressor across the output
terminals of the power circuit to prevent a surge voltage
from being generated. The surge suppressor must keep the
surge voltage, if generated, from exceeding the breakdown
voltage of each element in the power circuit.
that flows through the power circuit upon power application.
Although the resistance of R is determined according to the
resistance of the load coil and the ratings of the diodes, the
use of a resistor having a resistance of 0.1 to 100Ω is rec-
ommended.
large as possible to reduce the ripple percentage.
1
of low-tension overhead wiring (cable length: 200 to 500 m).
is a smoothing capacitor. Its capacitance must be as
1
to B
4
are used to protect the
Electromechanical Relays
Internal surge
2. The cable for connecting the surge suppressor must be as short
3. When using a surge suppressor between cable and ground, the
■ Countermeasures Against
In case the supply voltage fluctuates heavily, insert a regulated volt-
age circuit or constant-voltage circuit in the application circuit as
shown below.
Relays consume more power than semiconductor elements. The fol-
lowing circuit configuration is recommended to improve the charac-
teristics.
as possible in length, and thick enough in diameter so that it can
sufficiently withstand the surge current. The short length and thick
diameter are important to reduce the inductance and generated
voltage, and to protect the device from heat damage.
lower the ground resistance of the surge suppressor, the better
the protective effect of the surge suppressor. Perform grounding
at a ground resistance of 10Ω or less.
Supply Voltage Fluctuation
Technical Information
25