Z8F08200100KIT Zilog, Z8F08200100KIT Datasheet - Page 23

no-image

Z8F08200100KIT

Manufacturer Part Number
Z8F08200100KIT
Description
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer
Zilog
Series
Z8 Encore!®r
Type
MCUr
Datasheets

Specifications of Z8F08200100KIT

Contents
Evaluation Board, Cable, Power Supply, Software and Documentation
Data Bus Width
8 bit
Interface Type
RS-485
Silicon Manufacturer
Zilog
Core Architecture
Z8 Encore
Silicon Core Number
Z8F0822SJ020
Silicon Family Name
XP F0822
For Use With/related Products
Z8 Encore!™
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3183
Table 3. Signal Descriptions (Continued)
PS022517-0508
Signal
Mnemonic
SPI Controller
SS
SCK
MOSI
MISO
UART Controllers
TXD0
RXD0
CTS0
DE0
Timers
T0OUT /
T1OUT
T0IN / T1IN
Analog
ANA[4:0]
VREF
I/O
I/O
I/O
I/O
I/O
O
O
O
I
I
I
I
I
Description
Slave Select—This signal can be an output or an input. If the
is the SPI Master, this pin can be configured as the Slave Select output. If the
Z8 Encore! XP
multiplexed with a GPIO pin.
SPI Serial Clock—The SPI Master supplies this pin. If the
the SPI Master, this pin is the output. If the
this pin is the input. It is multiplexed with a GPIO pin.
Master-Out/Slave-In—This signal is the data output from the SPI Master
device and the data input to the SPI Slave device. It is multiplexed with a GPIO
pin.
Master-In/Slave-Out—This pin is the data input to the SPI Master device and
the data output from the SPI Slave device. It is multiplexed with a GPIO pin.
Transmit Data—This signal is the transmit output from the UART and IrDA.
The TXD signals are multiplexed with GPIO pins.
Receive Data—This signal is the receiver input for the UART and IrDA. The
RXD signals are multiplexed with GPIO pins.
Clear To Send—This signal is control inputs for the UART. The CTS signals
are multiplexed with GPIO pins.
Driver Enable—This signal allows automatic control of external RS-485
drivers. This signal is approximately the inverse of the TXE (Transmit Empty)
bit in the UART Status 0 Register. The DE signal can be used to ensure the
external RS-485 driver is enabled when data is transmitted by the UART.
Timer Output 0–1—These signals are output pins from the timers. The Timer
Output signals are multiplexed with GPIO pins.
Timer Input 0–1—These signals are used as the Capture, Gating and Counter
inputs. The Timer Input signals are multiplexed with GPIO pins.
Analog Input—These signals are inputs to the Analog-to-Digital Converter
(ADC). The ADC analog inputs are multiplexed with GPIO pins.
Analog-to-Digital Converter reference voltage input—As an output, the
VREF signal is not recommended for use as a reference voltage for external
devices. If the ADC is configured to use the internal reference voltage
generator, this pin should be left unconnected or capacitively coupled to
analog ground (AVSS).
is the SPI Slave, this pin is the input slave select. It is
Z8 Encore! XP
Z8 Encore! XP
Product Specification
Signal and Pin Descriptions
Z8 Encore! XP
is the SPI Slave,
Z8 Encore! XP
®
F0822 Series
is
®
10

Related parts for Z8F08200100KIT