EVAL-AD7739EBZ Analog Devices Inc, EVAL-AD7739EBZ Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
EVAL-AD7739EBZ
Manufacturer Part Number
EVAL-AD7739EBZ
Description
BOARD EVAL FOR AD7739
Manufacturer
Analog Devices Inc
Datasheet
1.AD7739BRUZ.pdf
(32 pages)
Specifications of EVAL-AD7739EBZ
Number Of Adc's
1
Number Of Bits
24
Sampling Rate (per Second)
15.1k
Data Interface
Serial
Inputs Per Adc
8 Single Ended
Input Range
±2.5 V
Power (typ) @ Conditions
85mW @ 5 V
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 105°C
Utilized Ic / Part
AD7739
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
RESET
The AD7739 can be reset by the RESET pin or by writing a reset
sequence to the AD7739 serial interface. The reset sequence is
N × 0 + 32 × 1, which could be the data sequence 0x00 + 0xFF +
0xFF + 0xFF + 0xFF in a byte-oriented interface.
The AD7739 also features a power-on reset with a trip point
of 2 V and goes to the defined default state after power-on.
It is the system designer’s responsibility to prevent an unwanted
write operation to the AD7739. The unwanted write operation
could happen when a spurious clock appears on the SCLK while
the CS pin is low. Note that if the AD7739 interface signals are
floating or undefined at system power-on, the part can be
inadvertently configured into an unknown state. This could be
easily overcome by initiating either a hardware reset event or a
32 ones reset sequence as the first step in the system
configuration.
ACCESS THE AD7739 REGISTERS
All communications to the part start with a write operation to
the communications register followed by either reading or
writing the addressed register. In a simultaneous read-write
interface (such as SPI), write 0 to the AD7739 while reading
data.
Figure 16 shows the AD7739 interface read sequence for the
ADC status register.
DOUT
SCLK
RDY
DIN
CS
COMMUNICATIONS
DOUT
SCLK
RDY
CS
DIN
REGISTER
WRITE
0x38
Figure 18. Serial Interface Signals—Single Conversion Command, 16-Bit Data Reading, Dump Mode
COMMUNICATIONS
REGISTER
Figure 17. Serial Interface Signals—Single Conversion Command and 16-Bit Data Reading
WRITE
0x38
REGISTER
WRITE
MODE
0x48
REGISTER
WRITE
MODE
0x40
CONVERSION TIME
CONVERSION TIME
Rev. 0 | Page 23 of 32
COMMUNICATIONS
REGISTER
WRITE
0x48
COMMUNICATIONS
SINGLE CONVERSION AND READING DATA
When the mode register is being written, the ADC status byte
is cleared and the RDY pin goes high, regardless of its previous
state. When the single conversion command is written to the
mode register, the ADC starts the conversion on the channel
selected by the address of the mode register. After the
conversion is completed, the data register is updated, the mode
register is changed to idle mode, the relevant RDY bit is set,
and the RDY pin goes low. The RDY bit is reset and the RDY
pin returns high when the relevant channel data register is
being read.
Figure 17 shows the digital interface signals executing a single
conversion on Channel 0, waiting for the RDY pin to go low,
and reading the Channel 0 data register.
DUMP MODE
When the DUMP bit in the mode register is set to 1, the channel
status register will be read immediately by a read of the channel
data register, regardless of whether the status or the data register
has been addressed through the communications register. The
DIN pin should not be high while reading 24-bit data in dump
mode; otherwise, the AD7739 will be reset.
Figure 18 shows the digital interface signals executing a single
conversion on Channel 0, waiting for the RDY pin to go low,
and reading the Channel 0 status register and data register in
the dump mode.
REGISTER
WRITE
0x48
CHANNEL
STATUS
STATUS
READ
(0x00)
(0x00)
DATA
READ DATA REGISTER
(0x00)
DATA
READ DATA
REGISTER
(0x00)
DATA
03742-0-017
(0x00)
DATA
03742-0-018
AD7739