OM6290 NXP Semiconductors, OM6290 Datasheet - Page 24

• Manufacturer Part Number: OM6290
• Description: DEMO BOARD LCD GRAPHIC DRIVER
• Manufacturer: NXP Semiconductors

Specifications of OM6290

• Main Purpose: Displays, LCD Controller
• Embedded: Yes, MCU, 16/32-Bit
• Utilized Ic / Part: PCF2119, PCF8531, PCF8576
• Primary Attributes: Character, Graphic and Segment LCD Drivers
• Secondary Attributes: JTAG, I²C, UART & USB Interfaces
• Description/function: Demo Board
• Interface Type: USB, I2C, JTAG, UART
• Data Bus Width: 4 bit, 8 bit, 16 bit
• Operating Voltage: 1.8 V to 5.5 V
• For Use With/related Products: PCF8576DT, PCF2119S, PCF8531
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4703

Philips Semiconductors
Table 12 BANK SELECT option 2
Table 13 BLINK option 1
Table 14 BLINK option 2
7.9
The display controller executes the commands identified
by the command decoder. It contains the status registers
of the PCF8576 and co-ordinates their effects. The
controller is also responsible for loading display data into
the display RAM as required by the filling order.
2001 Oct 02
RAM bit 0
RAM bit 2
Off
2 Hz
1 Hz
0.5 Hz
Normal blinking
Alternation blinking
Universal LCD driver for low multiplex rates
BLINK FREQUENCY
STATIC
Display controller
BLINK MODE
RAM bits 0 and 1
RAM bits 2 and 3
1 : 2 MUX
BF1
0
0
1
1
BIT A
BITS
0
1
BIT O
0
1
BF0
0
1
0
1
24
7.10
In large display configurations, up to 16 PCF8576s can be
distinguished on the same I
hardware subaddress (A0, A1 and A2) and the
programmable I
cascaded PCF8576s are synchronized so that they can
share the backplane signals from one of the devices in the
cascade. Such an arrangement is cost-effective in large
LCD applications since the backplane outputs of only one
device need to be through-plated to the backplane
electrodes of the display. The other PCF8576s of the
cascade contribute additional segment outputs but their
backplane outputs are left open-circuit (see Fig.18).
The SYNC line is provided to maintain the correct
synchronization between all cascaded PCF8576s. This
synchronization is guaranteed after the Power-on reset.
The only time that SYNC is likely to be needed is if
synchronization is accidentally lost (e.g. by noise in
adverse electrical environments; or by the definition of a
multiplex mode when PCF8576s with differing SA0 levels
are cascaded). SYNC is organized as an input/output pin;
the output selection being realized as an open-drain driver
with an internal pull-up resistor. A PCF8576 asserts the
SYNC line at the onset of its last active backplane signal
and monitors the SYNC line at all other times. Should
synchronization in the cascade be lost, it will be restored
by the first PCF8576 to assert SYNC. The timing
relationship between the backplane waveforms and the
SYNC signal for the various drive modes of the PCF8576
are shown in Fig.19.
For single plane wiring of packaged PCF8576s and
chip-on-glass cascading, see Chapter 12.
Cascaded operation
2
C-bus slave address (SA0). When
2
C-bus by using the 3-bit
Product specification
PCF8576