OKY2-T/16-D12P-C Murata Power Solutions Inc, OKY2-T/16-D12P-C Datasheet
OKY2-T/16-D12P-C
Specifications of OKY2-T/16-D12P-C
Related parts for OKY2-T/16-D12P-C
OKY2-T/16-D12P-C Summary of contents
Page 1
... Mechanical Specifi cations, Input/Output Pinout Detailed Electrical Specifi cations Output Voltage Adjustment, Soldering Guidelines Application Notes Performance Data – OKY2-T/10-D12 Performance Data and Oscillograms – OKY2-T/16-D12 Tape and Reel Information Product Label, MTBF Table Simplifi ed Block Diagram Controller Reference and Error Amplifi ...
Page 2
... OKY2-T/10-D12N-C 0.7525-5 OKY-T/16-D12P-C 0.7525-5 OKY-T/16-D12N-C 0.7525-5 OKY2-T/16-D12P-C 0.7525-5 OKY2-T/16-D12N-C 0.7525-5 ➀ Dimensions are in inches (mm). ➁ The input voltage range must be 13.2 Volts max. for Vout >= 3.63 V. ➂ All specifications are at nominal line voltage, Vout=nominal (5V for D12 models) and full load, +25 deg.C. ...
Page 3
... The Remote On/Off can be provided with either positive (P suffi negative (N suffi x) polarity. ** Vtrack Seq applies only to OKY2 models. No connection for OKY models. email: sales@murata-ps.com 18 Oct 2010 MDC_OKY_T10T16.D12.A06 Page Function P66 On/Off Control * +Vin Vtrack Seq** Gnd (Common) ...
Page 4
Performance and Functional Specifi cations See Note 1 Input Input Voltage Range See Ordering Guide. Start-Up Voltage 8.00V Undervoltage Shutdown (see Note 15) 7.75V) Overvoltage Shutdown None Refl ected (Back) Ripple Current (Note pk-pk Internal Input Filter ...
Page 5
... Also, avoid high noise at the Trim input. However, to prevent instability, you should never connect any capaci- tors to Trim. OKY2-T/10-D12, -T/16-D12 Output Voltage Calculated Rtrim (KΩ) 5.0 V. ...
Page 6
APPLICATION NOTES Input Fusing Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. We recommend ...
Page 7
COPPER STRIP +SENSE +OUTPUT C1 -OUTPUT COPPER STRIP C1 = 0.1μF CERAMIC C2 = 10μF TANTALUM LOAD 2-3 INCHES (51-76mm) FROM MODULE Figure 3: Measuring Output Ripple and Noise (PARD the shutdown temperature, an on-board electronic temperature sensor ...
Page 8
Dynamic control of the On/Off function must sink appropriate signal current when brought low and withstand appropriate voltage when brought high. Be aware too that there is a fi nite time in milliseconds (see Specifi cations) between the time of ...
Page 9
... 14V Load Curre nt (Amps) Programmable DOSA-SMT 10/16-Amp DC/DC Converters OKY2-T/10-D12 Effi ciency vs. Line Voltage and Load Current @ +25° OKY2-T/10-D12 Effi ciency vs. Line Voltage and Load Current @ +25° OKY2-T/10-D12 Effi ciency vs. Line Voltage and Load Current @ +25° www.murata-ps.com OKY -T/10 & T/16-D12 Series ...
Page 10
... 14V Load Curre nt (Amps) OKY2-T/10-D12-C Maximum Current Temperature Derating at Sea Level Programmable DOSA-SMT 10/16-Amp DC/DC Converters OKY2-T/10-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 12V 0.75 to 5V). IN OUT Natural convection Ambient Temperature (ºC) www.murata-ps.com OKY -T/10 & T/16-D12 Series (V = 5V) ...
Page 11
... OKY2-T/16-D12-C Maximum Current Temperature Derating at Sea Level OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 1.5V) OUT 12V 14V Load Curre nt (Amps) www.murata-ps.com OKY -T/10 & T/16-D12 Series (V = 12V 0.75V). IN ...
Page 12
... PERFORMANCE DATA AND OSCILLOGRAMS – OKY2-T/16-D12 On/Off Enable Startup Delay (Vin=8.3V, Vout=1.5V, Iout=16A, Cload=0) Trace 4=Enable In, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=1.5V, Cload=0, Iout=8A to 16A) Trace 2=Vout, 100 mV/div., Trace4=Iout, 5A/div. OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 1.8) OUT 90 ...
Page 13
... On/Off Enable Startup Delay (Vin=8.3V, Vout=2.5V, Iout=16A, Cload=0) Trace 4=Enable In, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=2.5V, Cload=0, Iout=8A to 16A) Trace 2=Vout, 100 mV/div., Trace4=Iout, 5A/div. Programmable DOSA-SMT 10/16-Amp DC/DC Converters OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 2.5V) OUT ...
Page 14
... PERFORMANCE DATA AND OSCILLOGRAMS – OKY2-T/16-D12 OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 3.3V) OUT 8. 12V 14V Load Curre nt (Amps) On/Off Enable Startup Delay (Vin=8.3V, Vout=3.3V, Iout=16A, Cload=0) Trace 4=Enable In, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=0, Iout=8A to 16A) Trace 2=Vout, 100 mV/div ...
Page 15
... PERFORMANCE DATA AND OSCILLOGRAMS – OKY2-T/16-D12 OKY2-T/16-D12 Effi ciency vs. Line Voltage and Load Current @ +25° 5V) OUT 8. 12V 13. Load Curre nt (Amps) On/Off Enable Startup Delay (Vin=8.3V, Vout=5V, Iout=16A, Cload=0) Trace 4=Enable In, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=5V, Cload=0, Iout=8A to 16A) Trace 2=Vout, 100 mV/div., Trace4=Iout, 5A/div. ...
Page 16
TAPE & REEL IMFORMATION 2.00 .079 (P/U) 18.19 .716 (P/U) 44.00 1.732 2.00 .079 PIN #1 THIS CORNER (FARSIDE) PICKUP NOZZLE LOCATION ( 3-6mm) PICK & PLACE PICKUP (P/U) Programmable DOSA-SMT 10/16-Amp DC/DC Converters FEED (UNWIND) DIRECTION ------- 4.00 .157 ...
Page 17
... OKY-T/10-D12P-C OKY-T/10-D12N-C OKY2-T/10-D12P-C OKY2-T/10-D12N-C OKY-T/16-D12P-C OKY-T/16-D12N-C OKY2-T/16-D12P-C OKY2-T/16-D12N-C The manufacturing date code is four characters: First character – Last digit of manufacturing year, example 2009 Second character – Month code (1 through 9 and O through D) Third character – Day code (1 through 10=O and 11 through through Z) Fourth character – ...