OKR-T/3-W12-C Murata Power Solutions Inc, OKR-T/3-W12-C Datasheet
OKR-T/3-W12-C
Specifications of OKR-T/3-W12-C
Related parts for OKR-T/3-W12-C
OKR-T/3-W12-C Summary of contents
Page 1
... Adjustable Output 3-Amp SIP-mount DC/DC Converters The OKR-T/3 series are miniature SIP non-isolated Point-of-Load (PoL) DC/DC power converters measuring only 0.41 x 0.65 x 0.22 inches (10.4 x 16.5 x 5.6 mm). The wide input range is 4 Volts DC. Based on 600 KHz synchronous buck topology, the high power conversion effi cient Point of Load (PoL) module features programmable output voltage and On/Off control, under voltage lock out (UVLO), overcur- rent and over temperature protections. These units are certifi ...
Page 2
... E = Forced enable, open pin = OFF, see specs Wide Input Voltage Range W12 = 4.5 – 14 Volts Maximum Rated Output Current in Amps OKR-T/3-W12-C OKR-T/3-W12E-C The manufacturing date code is four characters: First character – Last digit of manufacturing year, example 200 Second character – Month code (1 through 9 and O through D) Third character – ...
Page 3
... Output Trim www.murata-ps.com/support Adjustable Output 3-Amp SIP-mount DC/DC Converters 0.30 (7.62) 0.20 (5.1) Pin #1 0.032 (0.81) 0.067 (1.7) 0.134 (3.4) Figure 3. OKR Series Component locations are typical. 0.22 (5.6) 0.12 0.05 (3.05) (1.3) REF THK 0.15 (3.8) 0.032 (0.81) 0.05 (1.3) Dimensions are in inches (mm shown for ref. only). Tolerances (unless otherwise specifi ...
Page 4
... A/μSec Switching Frequency 600 KHz Calculated MTBF (Note 4) OKR-T/3-W12-C 12,230,400 hours (4a) OKR-T/3-W12-C 5,273,231 hours (4b) Operating Temperature Range (Ambient temp., Vout=5 V., vertical mount) Full power, see derating curves -40 to +85 °C. Operating PC Board Range, no derating -40 to +100 °C. ...
Page 5
All specifi cations are typical unless noted. General conditions for Specifi cations are +25 deg.C, Vin=nominal, Vout=nominal (no trim installed), full rated load. Adequate airfl ow must be supplied for extended testing under power. All models are tested and ...
Page 6
Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. For greatest safely, we recommend a ...
Page 7
COPPER STRIP +OUTPUT C1 -OUTPUT COPPER STRIP C1 = 0.1μF CERAMIC C2 = 10μF TANTALUM LOAD 2-3 INCHES (51-76mm) FROM MODULE Figure 5. Measuring Output Ripple and Noise (PARD) All models regulate within specifi cation and are stable under no ...
Page 8
... If you wish to control the On/Off circuit by external logic rather than a switch, carefully compare your logic threshold voltages with that of the On/Off input. On/Off Control Min. Vgs for turn-on = 2.0V. Max. Vgs for turn-off = 0.4V. OKR-T/3-W12-C PERFORMANCE DATA Effi ciency vs. Line Voltage and Load Current @ 25°C 100 95 V ...
Page 9
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 1V On/Off Enable Startup (Vin=13.8V, Vout=1V, Iout=3A, Cload=0) Trace 4=Enable, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=1V, Cload=0, Iout=1.5A to 3A) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 1A/div. www.murata-ps.com/support Adjustable Output 3-Amp SIP-mount DC/DC Converters Output Ripple and Noise (Vin=12V, Vout=1V, Iout=3A, Cload=0, ScopeBW=100MHz) Step Load Transient Response (Vin=12V, Vout=1V, Cload=0, Iout= ...
Page 10
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 2.5V On/Off Enable Startup (Vin=13.8V, Vout=2.5V, Iout=3A, Cload=0) Trace 4=Enable, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=2.5V, Cload=0, Iout=1.5A to 3A) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 1A/div. www.murata-ps.com/support Adjustable Output 3-Amp SIP-mount DC/DC Converters Output Ripple and Noise (Vin=12V, Vout=2.5V, Iout=3A, Cload=0, ScopeBW=100MHz) Step Load Transient Response (Vin=12V, Vout=2 ...
Page 11
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 5V On/Off Enable Startup (Vin=13.8V, Vout=5V, Iout=3A, Cload=0) Trace 4=Enable, Trace2=Vout Step Load Transient Response (Vin=12V, Vout=5V, Cload=0, Iout=1.5A to 3A) Trace 2=Vout, Trace 4=Iout, 1A/div. Murata Power Solutions recommends the specifi cations below when installing these converters. These specifi cations vary depending on the solder type. Exceeding these specifi ca- tions may cause damage to the product. Your production environment may differ ...
Page 12
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 1.8V Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=12x10μ ...
Page 13
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 1.8V Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=10x10μ ...
Page 14
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 3.3V Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=12x10μ ...
Page 15
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 3.3V Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=10x10μ ...
Page 16
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 5V Step Load Transient Response (Vin=12V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=12x10μ ...
Page 17
... OKR-T/3-W12-C OSCILLOGRAMS – Vout = 5V Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 3A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=10x10μ ...