DFC10E24S5 POWER ONE, DFC10E24S5 Datasheet - Page 2
![CONVERTER DC-DC 10W 5V SGL](/photos/8/59/85994/dfc10e24s5_sml.jpg)
DFC10E24S5
Manufacturer Part Number
DFC10E24S5
Description
CONVERTER DC-DC 10W 5V SGL
Manufacturer
POWER ONE
Series
DFC10r
Type
Isolatedr
Specifications of DFC10E24S5
Output
5V
Number Of Outputs
1
Power (watts)
10W
Mounting Type
Through Hole
Voltage - Input
18 ~ 36V
Package / Case
5-DIP Module (4 Leads)
1st Output
5 VDC @ 2A
Size / Dimension
2.02" L x 1.02" W x 0.42" H (51.3mm x 25.9mm x 10.7mm)
Power (watts) - Rated
10W
Operating Temperature
-50°C ~ 100°C
Efficiency
83%
Approvals
CE, cUL, TUV, UL
Product
Isolated
Output Power
10 W
Input Voltage Range
18 V to 36 V
Output Voltage (channel 1)
5 V
Output Current (channel 1)
2000 mA
Isolation Voltage
700 V
Package / Case Size
2.02 in x 1.02 in
Output Type
Isolated
Brand/series
DFC10 Series
Configuration
Enclosed
Current, Output
2000 mA
Dimensions
2.02 in. W x 1.02 in. H
Operation
Switching
Power, Output
10 W
Primary Type
DC-DC Converter
Temperature, Operating, Maximum
+90 °C
Temperature, Operating, Minimum
-40 °C
Voltage, Input
18 to 36 VDC
Voltage, Output
5 VDC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
3rd Output
-
2nd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
179-1012
MCD10005 Rev. 1.2, 15-Jun-10
NOTES
(1) All parameters measured at Tc = 25°C, nominal input voltage and full
rated load unless otherwise noted.
(2) Noise measurement bandwidth is 0-20 MHz for peak-peak
measurements, 10 kHz to 1 MHz for RMS measurements. Output noise is
measured with a 0.01μF / 100V ceramic capacitor in parallel with a 1μf / 35V
Tantalum capacitor, 1 inch from the output pins to simulate standard PCB
decoupling capacitance.
(3) Short term stability is specified after a 30 minute warmup at full load,
constant line and recording the drift over a 24 hour period.
(4) The input ripple rejection is specified for DC to 120 Hz ripple with a
modulation amplitude of 1% of Vin.
DFC10 SERIES APPLICATION NOTES
External Capacitance Requirements:
No external capacitance is required for operation of the DFC10 Series. If a
capacitive input source is farther than 1” from the converter, an additional
DFC10 Single-Output DC-DC Series Data Sheet
Page 2 of 3
capacitor may be required at the input pins for proper operation.
This input capacitor should have an ESR greater than 0.25
ohms. Input capacitors with an ESR less than 0.25 ohms may
cause peaking of the input filter and actually degrade circuit
performance.
External output capacitance is not required for operation.
However, it is recommended that 1 μF to 10 μF of tantalum and
0.001 to 0.1 μF ceramic capacitance be selected for reduced
system noise. Additional output capacitance may be added for
increased filtering, but should not exceed 400 μF.
Negative Outputs:
A negative output voltage may be obtained by connecting the
+OUT to circuit ground and connecting -OUT as the negative
output.
www.power-one.com