SI8462BB-A-IS1R Silicon Laboratories Inc, SI8462BB-A-IS1R Datasheet - Page 16
![IC ISOLATOR DGTL 6CH 16SOIC](/photos/6/80/68073/16-soic__3_9mmwidth__sml.jpg)
SI8462BB-A-IS1R
Manufacturer Part Number
SI8462BB-A-IS1R
Description
IC ISOLATOR DGTL 6CH 16SOIC
Manufacturer
Silicon Laboratories Inc
Series
ISOpror
Datasheet
1.SI8462AB-A-IS1.pdf
(36 pages)
Specifications of SI8462BB-A-IS1R
Inputs - Side 1/side 2
4/2
Number Of Channels
6
Isolation Rating
2500Vrms
Voltage - Supply
2.7 V ~ 5.5 V
Data Rate
150Mbps
Propagation Delay
6ns
Output Type
Logic
Package / Case
16-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 125°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 5. Electrical Characteristics
(V
Si8460/61/62/63
Table 6. Regulatory Information*
16
Parameter
All Models
Output Rise Time
Output Fall Time
Common Mode Transient
Immunity at Logic Low Output
Start-up Time
Notes:
CSA
The Si84xx is certified under CSA Component Acceptance Notice 5A. For more details, see File 232873.
61010-1: Up to 300 V
60950-1: Up to 130 V
VDE
The Si84xx is certified according to IEC 60747-5-2. For more details, see File 5006301-4880-0001.
60747-5-2: Up to 560 V
UL
The Si84xx is certified under UL1577 component recognition program. For more details, see File E257455.
Rated up to 2500 V
*Note: Regulatory Certifications apply to 2.5 kV
DD1
1. Specifications in this table are also valid at VDD1 = 2.6 V and VDD2 = 2.6 V when the operating temperature range is
2. The nominal output impedance of an isolator driver channel is approximately 85 , ±40%, which is a combination of the
3. t
4. Start-up time is the time period from the application of power to valid data at the output.
= 2.70 V, V
constrained to T
value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
same supply voltages, load, and ambient temperature.
For more information, see "5. Ordering Guide" on page 29.
PSK(P-P)
4
is the magnitude of the difference in propagation delay times measured between different units operating at the
DD2
= 2.70 V, T
RMS
A
RMS
RMS
= 0 to 85 °C.
peak
isolation voltage for basic insulation.
reinforced insulation working voltage; up to 600 V
reinforced insulation working voltage; up to 600 V
for basic insulation working voltage.
A
= –40 to 125 ºC; applies to narrow-body SOIC package)
Symbol
CMTI
1
t
SU
t
t
r
f
(Continued)
RMS
rated devices which are production tested to 3.0 kV
Test Condition
V
See Figure 1
See Figure 1
I
C
C
= V
L
L
Rev. 1.3
= 15 pF
= 15 pF
DD
or 0 V
Min
—
—
—
—
RMS
RMS
basic insulation working voltage.
basic insulation working voltage.
Typ
4.8
3.2
25
15
RMS
for 1 sec.
Max
6.5
4.6
40
—
kV/µs
Unit
ns
ns
µs