GNM314R71C683MA01L Murata Electronics North America, GNM314R71C683MA01L Datasheet - Page 55

CAP 4-ARRAY 68000PF 16V X7R 1206

GNM314R71C683MA01L

Manufacturer Part Number
GNM314R71C683MA01L
Description
CAP 4-ARRAY 68000PF 16V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R71C683MA01L

Capacitance
0.068µF
Voltage - Rated
16V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±20%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3444-2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
11
12 Deflection
13
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
Continued from the preceding page.
Vibration
Resistance
Solderability of
Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
Item
Appearance
Capacitance
Q/D.F.
Appearance
Capacitance
Change
No defects or abnormalities
Within the specified tolerance
30pF and over: QU1000
30pF and below:
C: Nominal Capacitance (pF)
No marking defects
Within 5% or 0.5pF
(whichever is larger)
75% of the terminations are to be soldered evenly and
continuously.
Compensating Type
Temperature
QU400+20C
R230
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
Specifications
Capacitance meter
45
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
Fig. 3a
20
[B1, B3, R6, R7, C8]
W.V.: 100V
W.V.: 50/35/25V:
*GRM32D R7/R6/C8 1E106: 0.035 max.
W.V.: 16/10V: 0.035 max.
W.V.: 6.3/4V
[E4]
W.V.: 25Vmin: 0.025 max.
[F1, F5]
W.V.: 25V min.
W.V.: 16/10V: 0.125 max.
W.V.: 6.3V: 0.15 max.
Within 10%
50
Please refer to individual specifications (our product specifications or the approval sheet).
Pressurize
45
Pressurizing
speed: 1.0mm/sec.
High Dielectric Type
: 0.025 max. (CF0.068 F)
: 0.05 max. (CU0.068 F)
: 0.025 max.*
: 0.05 max. (CF3.3 F)
: 0.1 max. (CU3.3 F)
: 0.05 max. (CF0.1 F)
: 0.09 max. (CU0.1 F)
Flexure : V1
(Note 1) These Specifications and Test Methods indicate typical inspection.
Solder the capacitor on the test jig (glass epoxy board) in the
same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2a using a eutectic solder. Then apply a force in the
direction shown in Fig. 3a for 5 1 sec. The soldering should be
done by the reflow method and should be conducted with care
so that the soldering is uniform and free of defects such as heat
shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion).
Preheat at 80 to 120 C for 10 to 30 seconds.
After preheating, immerse in a eutectic solder solution for
2 0.5 seconds at 230 5 C or Sn-3.0Ag-0.5Cu solder solution
for 2 0.5 seconds at 245 5 C.
GRM02
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
Type
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
Test Method
a
Fig. 2a
100
b
c
a
Continued on the following page.
t: 1.6mm (GRM02/03/15: t: 0.8mm)
0.56
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
b
4.5
0.23
1.65
0.3
0.5
1.2
2.0
2.9
3.7
5.6
c
(in mm)
53
C02E.pdf
10.12.20

Related parts for GNM314R71C683MA01L