GNM314R71C683MA01L Murata Electronics North America, GNM314R71C683MA01L Datasheet - Page 143

CAP 4-ARRAY 68000PF 16V X7R 1206

GNM314R71C683MA01L

Manufacturer Part Number
GNM314R71C683MA01L
Description
CAP 4-ARRAY 68000PF 16V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R71C683MA01L

Capacitance
0.068µF
Voltage - Rated
16V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±20%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3444-2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
6. Electrical Test on Printed Circuit Board
1. Confirm position of the support pin or specific jig, when
7. Printed Circuit Board Cropping
1. After mounting a capacitor on a printed circuit board, do
2. Ascertain of the cropping method for the printed circuit
!Caution
inspecting the electrical performance of a capacitor after
mounting on the printed circuit board.
1-1. Avoid bending printed circuit board by the pressure
1-2. Avoid vibration of the board by shock when a test pin
not apply any stress to the capacitor that is caused by
bending or twisting the board.
1-1. In cropping the board, the stress as shown right may
board in advance.
2-1. Printed circuit board cropping shall be carried out by
Continued from the preceding page.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
of a test pin, etc.
The thrusting force of the test probe can flex the PCB,
resulting in cracked chips or open solder joints.
Provide support pins on the back side of the PCB to
prevent warping or flexing.
contacts a printed circuit board.
cause the capacitor to crack.
Try not to apply this type of stress to a capacitor.
using a jig or an apparatus to prevent the mechanical
stress that can occur to the board.
(1) Example of a suitable jig
Recommended example: the board should be
pushed as close to the cropping jig as possible
and from the back side of board in order to
minimize the compressive stress applied to
capacitor.
Not recommended example: when the board is
pushed at a point far from the cropping jig and
from the front side of board as below, the
capacitor may form a crack caused by the tensile
stress applied to capacitor.
Printed Circuit Board
Recommended
Components
Load Point
Direction of Load
[Not Recommended]
[Recommended]
[Outline of Jig]
Printed Circuit Board
Printed Circuit Board
[Bending]
[Twisting]
Load Point
Not recommended
Components
Continued on the following page.
Test-pin
Board Cropping Jig
Test-pin
Direction of Load
V-groove
Peeling
!Caution
Support Pin
141
C02E.pdf
10.12.20

Related parts for GNM314R71C683MA01L