GNM314R72A681KD01D Murata Electronics North America, GNM314R72A681KD01D Datasheet - Page 47

CAP 4-ARRAY 680PF 100V X7R 1206

GNM314R72A681KD01D

Manufacturer Part Number
GNM314R72A681KD01D
Description
CAP 4-ARRAY 680PF 100V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R72A681KD01D

Capacitance
680pF
Voltage - Rated
100V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±10%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3419-2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
10
11
1
2
3
4
5
6
7
8
9
Capacitance
Temperature
Characteristics
Vibration
Operating
Temperature Range
Rated Voltage
Appearance
Dimensions
Dielectric Strength
Insulation Resistance
Capacitance
Dissipation Factor
(D.F.)
Adhesive Strength
of Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
D.F.
R6: Y55°C to +85°C
See the previous pages.
No defects or abnormalities
Within the specified dimension
No defects or abnormalities
50Ω · F min.
Within the specified tolerance
0.1 max.
No removal of the terminations or other defects should occur.
No defects or abnormalities
Within the specified tolerance
0.1 max.
Char.
R6
Temp. Range
Y55 to +85°C
Specifications
b
a
Fig. 1
Copper foil
Reference
Solder resist
Temp.
25°C
GNM Series Specifications and Test Methods (2)
Cap. Change
Within T15%
The rated voltage is defined as the maximum voltage which
may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage,
whichever is larger, should be maintained within the rated
voltage range.
Visual inspection
Using calipers
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 25°C and 75%RH
max. and within 1 minute of charging.
The capacitance/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
The capacitance change should be measured affter 5 min.at
each specified temperature stage.
value over the temperature ranges shown in the table should be
within the specified ranges.
• Initial measurement for high dielectric constant type.
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 1 using a eutectic solder.
Then apply 5N force in parallel with the test jig for 10T1 sec. The
soldering should be done either with an iron or using the reflow
method and should be conducted with care so that the soldering
is uniform and free of defects such as heat shock.
Solder the capacitor to the test jig (glass epoxy board) in
the same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz.
The frequency range, from 10 to 55Hz and return to 10Hz,
should be traversed in approximately 1 minute. This motion
should be applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
The ranges of capacitance change compared with the 25°C
Perform a heat treatment at 150+0/-10°C for one hour and
then set for 24T2 hours at room temperature.
Perform the initial measurement.
Capacitance
GNM1M2
GNM212
Type
Step
1
2
3
4
5
R6
0.5
0.6
a
Test Method
Frequency
1T0.1kHz
Continued on the following page.
Temperature (D)
1.6
1.8
b
Y55T3
25T2
25T2
85T3
25T2
0.32
0.5
c
0.5T0.1Vrms
Voltage
VP-P
or V
(in mm)
0.32
0.5
d
O-P
,
C02E.pdf
45
07.2.6
7

Related parts for GNM314R72A681KD01D