GNM314R72A681KD01D Murata Electronics North America, GNM314R72A681KD01D Datasheet - Page 38

CAP 4-ARRAY 680PF 100V X7R 1206

GNM314R72A681KD01D

Manufacturer Part Number
GNM314R72A681KD01D
Description
CAP 4-ARRAY 680PF 100V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R72A681KD01D

Capacitance
680pF
Voltage - Rated
100V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±10%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3419-2
6
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
36
No.
10
11
12
Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Capacitance
Temperature
Characteristics
Vibration
Resistance
Temperature
Cycle
Operating
Temperature
Range
Rated Voltage
Appearance
Dimensions
Dielectric Strength
Insulation Resistance
Capacitance
Dissipation Factor
(D.F.)
Mechanical
Strength
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
No bias
Bond
Strength
Die Shear
Strength
Appearance
Capacitance
D.F.
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
R7: Y55 to W125D
See the previous pages.
No defects or abnormalities
Within the specified dimersions
No defects or abnormalities
10,000MΩ min.
Within the specified tolerance
R7: 0.035 max.
R7: Within W/–15% (–55 to W125°C)
Pull force: 0.03N min.
Die Shear force: 2N min.
No defects or abnormalities
Within the specified tolerance
R7: 0.035 max.
No defects or abnormalities
R7: Within T7.5%
R7: 0.035 max.
10,000MΩ min.
No defects
Specifications
Reference Temperature: 25D
The rated voltage is defined as the maximum voltage which
may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, V
whichever is larger, should be maintained within the rated voltage
range.
Using calipers
Visual inspection
No failure should be observed when a voltage of 250% of the
rated voltage is applied between the both terminations for 1 to 5
seconds, provided the charge/discharge current is less than
50mA.
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at normal temperature
and humidity and within 2 minutes of charging.
The capacitance/D.F. should be measured at reference
temperature at the frequency and voltage shown in the table.
The capacitance change should be measured after 5min. at
each specified temp. stage.
#The ranges of capacitance change compared with the
Reference Temperature value over the temperature ranges
shown in the table should be within the specified ranges.
In case of applying voltage, the capacitance change should be
measured after 1 more min. with applying voltage in
equilibration of each temp. stage.
*Initial measurement for high dielectric constant type
Perform a heat treatment at 150 W0/Y10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
MIL-STD-883 Method 2011 Condition D
Mount the capacitor on a gold metallized alumina substrate with
Au-Sn (80/20) and bond a 25 m (0.0008 inch) gold wire to the
capacitor terminal using an ultrasonic ball bond. Then, pull wire.
MIL-STD-883 Method 2019
Mount the capacitor on a gold metallized alumina substrate
with Au-Sn (80/20). Apply the force parallel to the substrate.
Ramp frequency from 10 to 55Hz then return to 10Hz all within
1 minute. Amplitude: 1.5 mm (0.06 inch) max. total excursion.
Apply this motion for a period of 2 hours in each of 3 mutually
perpendicular directions (total 6 hours).
The capacitor should be set for 24T2 hours at room
temperature after one hour heat of treatment at 150W0/Y10D,
then measure for the initial measurement. Fix the capacitor to
the supporting jig in the same manner and under the same
conditions as (11) and conduct the five cycles according to the
temperatures and time shown in the following table. Set it for
48T4 hours at room temperature, then measure.
Temp. (D)
Time (min.)
Frequency
Voltage
Step
Step
1
2
3
4
Reference TemperatureT2
Reference TemperatureT2
Min. Operating
Temp. W0/Y3
Temperature (°C)
30T3
–55T3 (for R7)
125T3 (for R7)
–30T3 (for F5)
85T3 (for F5)
1
Test Method
Temp.
Room
2 to 3
Continued on the following page.
2
1T0.1kHz
1T0.2Vrms
Max. Operating
Temp. W3/Y0
30T3
Applying Voltage (V)
3
No bias
P-P
Temp.
Room
2 to 3
or V
4
*
O-P
,
C02E.pdf
07.2.6

Related parts for GNM314R72A681KD01D