GNM314R72A681KD01D Murata Electronics North America, GNM314R72A681KD01D Datasheet - Page 34

CAP 4-ARRAY 680PF 100V X7R 1206

GNM314R72A681KD01D

Manufacturer Part Number
GNM314R72A681KD01D
Description
CAP 4-ARRAY 680PF 100V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R72A681KD01D

Capacitance
680pF
Voltage - Rated
100V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±10%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3419-2
5
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
32
No.
14
15
16
17 Durability
*2: GRM31CR60J107: 0.15 max.
GRM Series Specifications and Test Methods (2)
Continued from the preceding page.
Resistance
to
Soldering
Heat
Temperature
Sudden
Change
High
Temperature
High
Humidity
(Steady)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Appearance
Capacitance
Change
D.F.
I.R.
No defects or abnormalities
B1, B3, R6, R7, C7, C8: Within T7.5%
F1, F5: Within T20%
B1, B3, R6*
F1, F5: 0.2 max.
More than 50Ω · F
No defects
No defects or abnormalities
B1, B3, R6, R7, C7, C8: Within T7.5%
F1, F5: Within T20%
B1, B3, R6*
F1, F5: 0.2 max.
More than 50Ω · F
No defects
No defects or abnormalities
B1, B3, R6, R7, C7, C8: Within T12.5%
F1, F5: Within T30%
B1, B3, R6, R7, C7, C8: 0.2 max.
F1, F5: 0.4 max.
More than 12.5Ω · F
No defects or abnormalities
B1, B3, R6, R7, C7, C8: Within T12.5%
F1, F5: Within T30%
B1, B3, R6, R7, C7, C8: 0.2 max.
F1, F5: 0.4 max.
More than 25Ω · F
2
2
In case "*" is not added in capacitance table, please refer to GRM Series Specifications and Test Methods (1) (P.24).
, R7, C7, C8: 0.1 max.
, R7, C7, C8: 0.1 max.
Specifications
Below GRM Series Specifications and Test Methods (2) are applied to "*" PNs in capacitance table.
*Do not apply to GRM02.
*Preheating for GRM32/43/55
Preheat the capacitor at 120 to 150D for 1 minute.
Immerse the capacitor in an eutectic solder or Sn-3.0Ag-0.5Cu
solder solution at 270T5D for 10T0.5 seconds. Set at room
temperature for 24T2 hours, then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150W0/Y10D for one hour and
then set at room temperature for 24T2 hours.
Perform the initial measurement.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
shown in the following table.
Set for 24 T 2 hours at room temperature, then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150W0/Y10D for one hour and
then set at room temperature for 24T2 hours.
Perform the initial measurement.
Apply the rated voltage at 40T2D and 90 to 95% humidity for
500T12 hours. The charge/discharge current is less than 50mA.
#Initial measurement
Perform a heat treatment at 150W0/Y10D for one hour and
then let sit for 24T2 hours at room temperature. Perform the
initial measurement.
#Measurement after test
Perform a heat treatment at 150W0/Y10D for one hour and
then let sit for 24T2 hours at room temperature, then measure.
Apply 150% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3D. Let sit for 24T 2 hours at
room temperature, then measure.
The charge/discharge current is less than 50mA.
#Initial measurement
Perform a heat treatment at 150W0/Y10D for one hour and
then let sit for 24T2 hours at room temperature. Perform the
initial measurement.
#Measurement after test
Perform a heat treatment at 150W0/Y10D for one hour and
then let sit for 24T2 hours at room temperature, then measure.
Temp. (D)
Time (min.)
Step
Step
1
2
Temp. W0/Y3
Operating
30T3
Min.
1
Temperature
100 to 120D
170 to 200D
Test Method
Temp.
Room
2 to 3
2
Temp. W3/Y0
Operating
30T3
Max.
3
1 min.
1 min.
Time
Temp.
Room
2 to 3
4
C02E.pdf
07.2.6

Related parts for GNM314R72A681KD01D