LT1019AIS8-2.5 Linear Technology, LT1019AIS8-2.5 Datasheet - Page 8
![IC REF PREC 2.5V .05% TOL 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT1019AIS8-2.5
Manufacturer Part Number
LT1019AIS8-2.5
Description
IC REF PREC 2.5V .05% TOL 8SOIC
Manufacturer
Linear Technology
Datasheet
1.LT1019CN8-5PBF.pdf
(12 pages)
Specifications of LT1019AIS8-2.5
Reference Type
Series, Shunt
Voltage - Output
2.5V
Tolerance
±0.05%
Temperature Coefficient
10ppm/°C
Voltage - Input
4 ~ 40 V
Number Of Channels
1
Current - Quiescent
1mA
Current - Output
10mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Cathode
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1019AIS8-2.5
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1019AIS8-2.5
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
LT1019
The worst-case error in initial output voltage for the
LT1019 is 0.2%, so a series resistor is satisfactory if the
output is simply trimmed to nominal value. The maximum
TC shift expected would be 1ppm/°C.
Using the Temp Pin
The LT1019 has a TEMP pin like several other bandgap
references. The voltage on this pin is directly propor-
tional to absolute temperature (PTAT) with a slope of
approximately 2.1mV/°C. Room temperature voltage is
therefore approximately (295°K)(2.1mV/°C) = 620mV.
This voltage varies with process parameters and should
not be used to measure absolute temperature, but
rather relative temperature changes. Previous bandgap
references have been very sensitive to any loading on
the TEMP pin because it is an integral part of the
reference “core” itself. The LT1019 “taps” the core at a
special point which has much less effect on the refer-
ence. The relationship between TEMP pin loading and
a change in reference output voltage is less than
0.05%/µA, about ten times improvement over previous
references.
Output Bypassing
The LT1019 is designed to be stable with a wide range of
load currents and output capacitors. The 4.5V, 5V, and
10V devices do not oscillate under any combination of
TYPICAL APPLICATIO S
8
V
IN
Wide Range Trim ≥ ±5%
U U
IN
LT1019
GND
TRIM
OUT
U
W
R1
25k
1019 TA03
V
OUT
U
capacitance and load. The 2.5V device can oscillate when
sinking currents between 1mA and 6mA for load capaci-
tance between 400pF and 2µF (see Figure 1).
If output bypassing is desired to reduce high frequency
output impedance, keep in mind that loop phase margin is
significantly reduced for output capacitors between 500pF
and 1µF if the capacitor has low ESR (Effective Series
Resistance). This can make the output “ring” with tran-
sient loads. The best transient load response is obtained
by deliberately adding a resistor to increase ESR as shown
in Figure 1.
Use configuration (a) if DC voltage error cannot be com-
promised as load current changes. Use (b) if absolute
minimum peak perturbation at the load is needed. For best
transient response, the output can be loaded with ≥ 1mA
DC current.
LT1019
V
IN
(a)
V
IN
+
*INCREASE TO 4.7M FOR LT1019A (±0.05%)
2Ω TO 5Ω
Narrow Trim Range (±0.2%)
2µF
TANTALUM
Figure 1. Output Bypassing
IN
LT1019
GND
TRIM
OUT
1.5M
LT1019
R2*
V
IN
(b)
2Ω TO 5Ω
R1
100k
1019 TA05
V
OUT
+
2µF TO 10µF
TANTALUM
1019fd
1019 F01