MIC2548-2YM Micrel Inc, MIC2548-2YM Datasheet - Page 12
![IC SW CURR LIMIT HI SIDE 8-SOP](/photos/6/50/65078/576-8-soic_sml.jpg)
MIC2548-2YM
Manufacturer Part Number
MIC2548-2YM
Description
IC SW CURR LIMIT HI SIDE 8-SOP
Manufacturer
Micrel Inc
Type
High Sider
Datasheet
1.MIC2544-1YM.pdf
(14 pages)
Specifications of MIC2548-2YM
Input Type
Non-Inverting
Number Of Outputs
1
On-state Resistance
80 mOhm
Current - Peak Output
1.5A
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Short Circuit Current Limit
0.1 to 1.5A
Input Voltage Range
2.7 to 5.5V
Number Of Switches
Single
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Package Type
SOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output / Channel
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-2178
MIC2548-2YM
MIC2548-2YM
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MIC2548-2YM
Manufacturer:
EPCOS
Quantity:
32 000
Part Number:
MIC2548-2YM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Company:
Part Number:
MIC2548-2YMM
Manufacturer:
MICREL
Quantity:
1 046
Part Number:
MIC2548-2YMM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Application Information
Supply Filtering
A 0.1μF to 1μF bypass capacitor from IN to GND,
located near the MIC2544 and MIC2548, is strongly
recommended to control supply transients. Without a
bypass capacitor, an output short may cause sufficient
ringing on the input (from supply lead inductance) to
damage internal control circuitry.
Input transients must not exceed the absolute maximum
supply voltage (V
Power Dissipation
The device's junction temperature depends on several
factors such as the load, PCB layout, ambient
temperature, and package type. Equations that can be
used to calculate power dissipation and junction
temperature are found below.
Calculation of power dissipation can be accomplished by
the following equation:
To relate this to junction temperature, the following
equation can be used:
Note: MSOP package option uses pin 5 for ILIM. Pin 4 is not connected (NC). Bold lines indicate 0.1” wide, 1-oz. copper high-current traces.
Micrel, Inc.
April 2010
PD = R
T
j
= P
D
DS(on)
× θ
Figure 3. Supply Bypassing
JA
IN max
× (I
+ T
OUT
= 6V) even for a short duration.
A
)
2
Figure 4. USB Host Application
12
where:
Transient Overcurrent Filter
The inrush current from the connection of a heavy
capacitive load may cause the fault flag to fall for 10μs to
200μs while the switch is in a constant-current mode,
charging the capacitance.
Adding an optional series resistor-capacitor (R
parallel with R
transient current-limit to be set to a different value than
steady state. A typical USB hot-plug inrush is 2A to 3A
for 10μs to 20μs. If R
88Ω (2.5A) and C
transient surge of 3A to pass for 100μs without tripping
the overcurrent flag (FLG).
USB Power Distribution
The MIC2544 is ideal for meeting USB power distribution
requirements. Figure 4 depicts a USB Host application.
RSET should be set to a value providing a current-limit
>500mA.
The accurate current-limit of the MIC2544 will reduce
power supply current requirements. Also, fast reaction to
short circuit faults prevent voltage droop in mobile
PC applications.
Printed Circuit Board Hot-Plug
The MIC2544/48 are ideal inrush current-limiters suitable
for hot-plug applications. Due to the integrated charge
pump, the MIC2544/48 presents a high impedance when
off and slowly becomes a low impedance as it turns on.
This “softstart” feature effectively isolates power supplies
from highly capacitive loads by reducing inrush current
during hot-plug events. Figure 5 shows how the
MIC2544 may be used in a hot-plug application.
T
T
θ
JA
j
A
= junction temperature
= ambient temperature
= is the thermal resistance of the package
SET
, as shown in Figure 4, allows the
SET
SET
of 1μF (RC = 100μs) allows
is 435Ω (510mA), an R
MIC2544/2548
M9999-043010
SET2
SET2
) in
of