LH28F160BJHE-TTL90 Sharp Microelectronics, LH28F160BJHE-TTL90 Datasheet - Page 30

• Manufacturer Part Number: LH28F160BJHE-TTL90
• Description: IC FLASH 16MBIT 90NS 48TSOP
• Manufacturer: Sharp Microelectronics

Specifications of LH28F160BJHE-TTL90

• Rohs Status: RoHS non-compliant
• Format - Memory: FLASH
• Memory Type: Boot Block FLASH
• Memory Size: 16M (2M x 8 or 1M x 16)
• Speed: 90ns
• Interface: Parallel
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TSOP
• Other names: 425-1824; LH28F160BJHE-BTL90; LHF16J04

6 ELECTRICAL SPECIFICATIONS
6.1 Absolute Maximum Ratings*
Operating Temperature
Storage Temperature
Voltage On Any Pin
V
V
Output Short Circuit Current................................100mA
6.2 Operating Conditions
6.2.1 CAPACITANCE
NOTE:
1. Sampled, not 100% tested.
T
V
C
C
sharp
Symbol
CC
CCW
A
CC
IN
OUT
Symbol
During Read, Block Erase,
Full Chip Erase, Word/Byte Write
and Lock-Bit Configuration .............-40°C to +85°C
During under Bias ............................... -40°C to +85°C
During non Bias ................................ -65°C to +125°C
(except V
Supply Voltage................................ -0.2V to +4.6V
Supply Voltage......................... -0.2V to +13.0V
Operating Temperature
V
CC
CC
Input Capacitance
Output Capacitance
Supply Voltage (2.7V-3.6V)
and V
CCW
Parameter
Parameter
) ........... -0.5V to V
(1)
Temperature and V
CC
+0.5V
T
A
(2,3)
=+25°C, f=1MHz
Typ.
(1)
(2)
(2)
(4)
LHF16J04
Min.
7
9
-40
2.7
CC
Operating Conditions
*WARNING: Stressing the device beyond the "Absolute
Maximum Ratings" may cause permanent damage. These
are stress ratings only. Operation beyond the "Operating
Conditions" is not recommended and extended exposure
beyond the "Operating Conditions" may affect device
reliability.
NOTES:
1. Operating temperature is for extended temperature
2. All specified voltages are with respect to GND.
3. Maximum DC voltage on V
4. Output shorted for no more than one second. No more
Max.
product defined by this specification.
Minimum DC voltage is -0.5V on input/output pins
and -0.2V on V
this level may undershoot to -2.0V for periods <20ns.
Maximum DC voltage on input/output pins are
V
V
+13.0V for periods <20ns. Applying 12V±0.3V to
V
maximum of 1000 cycles on each block. V
connected to 12V±0.3V for a total of 80 hours
maximum.
than one output shorted at a time.
10
12
Max.
+85
3.6
CC
CC
CCW
+0.5V which, during transitions, may overshoot to
+2.0V for periods <20ns.
during erase/write can only be done for a
Unit
pF
pF
Unit
CC
°C
V
and V
V
V
CCW
Ambient Temperature
IN
OUT
=0.0V
=0.0V
CCW
pins. During transitions,
Test Condition
Condition
may overshoot to
CCW
Rev. 1.26
may be
27