MAX5971BEVKIT+ Maxim Integrated, MAX5971BEVKIT+ Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
MAX5971BEVKIT+
Manufacturer Part Number
MAX5971BEVKIT+
Description
Power Management IC Development Tools
Manufacturer
Maxim Integrated
Series
MAX5971r
Datasheet
1.MAX5971BEVKIT.pdf
(22 pages)
Specifications of MAX5971BEVKIT+
Rohs
yes
4) Verify that a shunt is installed on jumper JU5 (legacy
5) Connect the -32V to -60V DC power supply to the
6) Connect a PD to the Ethernet output port RJ45 con-
7) Connect the EV kit’s network data input port J1 LAN
8) Turn on the power supply and set it to -54V.
9) Connect the USB cable from the PC to the EV kit
10) Follow the directions of the Found New Hardware
11) Start the EV kit software by opening its icon in the
12) Observe as the program automatically detects the
13) Select the BitMap Controls tab at the top of the GUI
14) Load and run the Power_on.smb macro program
15) The network output port’s yellow and green status
16) Four other example macros allow quick testing of
mode disabled) and on pins 1-5 of jumper JU7
(0x40 address).
metal VEE banana jack and the supply ground to
the metal GND banana jack. Do not turn on the
power supply until all connections are completed.
nector (J2) on the EV kit’s MagJack module. This
step is optional if network connectivity and/or a PD
is not required.
to the corresponding data LAN connection. Note:
This step is optional if network connectivity is not
required.
board. A New Hardware Found window pops up
when installing the USB driver for the first time.
If a window is not seen that is similar to the one
described above after 30s, remove the USB cable
from the board and reconnect it. Administrator privi-
leges are required to install the USB device driver
on Windows.
window to install the USB device driver. Manually
specify the location of the device driver to be
C:\Program Files\MAX5971B (default installation
directory) using the Browse button. During device
driver installation, Windows may show a warning
message indicating that the device driver Maxim
uses does not contain a digital signature. This is
not an error condition and it is safe to proceed
with installation. Refer to the USB_Driver_Help.PDF
document included with the software for additional
information.
Start | Programs menu.
USB interface circuit, starts the main program, and
then detects the I
for the IC.
(Figure 3).
from the File | Open | Run Macro menu bar. The
script automatically runs after selecting Open.
LEDs on J2 should be lit.
the manual mode, auto mode, semiauto mode,
_________________________________________________________________ Maxim Integrated Products 5
2
C-compatible address configured
17) Test points TP11, TP13 (VEE), and TP2 (GND) are
18) Pressing pushbutton switch SW1 shuts down the
Note: The GND banana jack is more positive than the
VEE or RTN banana jacks. Use an isolated oscillo-
scope for probing with respect to VEE or RTN.
Note: An uninstall program is included with the software.
Click on the UNINSTALL icon to remove the EV kit soft-
ware from the hard drive.
A mouse or the keyboard’s Tab key is used to navigate
various items on the main window (Figure 1). The EV kit
software features three tabs: Configuration, Events and
Status, and BitMap Controls. Most of the main window’s
available functions and a few more can be evaluated
by using the pulldown menu. The left status bar at the
bottom of the main window provides the USB interface
circuit status. The center status bar provides the current
EV kit and macro engine status.
Upon starting the program, the EV kit software starts in
the Auto Read state. The software automatically detects
the Slave Address and begins reading the contents
of each register from the IC, updating each tab sheet.
The software starts up with the Events and Status tab
selected.
The Events and Status tab sheet (Figure 1) provides
the EV kit’s system and port events/status information
obtained from the IC registers. The System Events and
Status group box provides system-level information on
the VEE power supply, present operating mode, and
address in hexadecimal and decimal formats. The Port
Events group box provides the PSE port event or change
status. The Port Status group box provides the PSE port
Detailed Description of Software
and with DC and/or AC load-disconnect detection.
These macros are:
Note: JU7 must be on pins 1-5 (0x40 address) for
these macros.
• TEST#1_MANUAL_MODE.SMB
• TEST#2_AUTO_MODE_DC.SMB
• TEST#3_AUTO_MODE_AC.SMB
• TEST#4_SEMIAUTO_MODE.SMB
provided on the PCB to observe the desired signals
with an oscilloscope or voltage meter. Use an
isolated oscilloscope for probing with respect to
VEE or RTN.
PSE output DC power and resets U1. The software
must be relaunched after a pushbutton reset.
Evaluates: MAX5971B
(JU6 not installed)
Events and Status Tab
Software Startup