MAX191EVKIT-DIP Maxim Integrated, MAX191EVKIT-DIP Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
MAX191EVKIT-DIP
Manufacturer Part Number
MAX191EVKIT-DIP
Description
Data Conversion IC Development Tools Evaluation System/Evaluation Kit for the MAX191
Manufacturer
Maxim Integrated
Series
MAX191r
Datasheet
1.MAX191EVKIT-DIP.pdf
(16 pages)
Specifications of MAX191EVKIT-DIP
Interface Type
Parallel, QSPI, Serial (SPI, Microwire)
The MAX191 EV system includes a Maxim 80C32 µC
module and a MAX191 EV kit. The two connect through a
40-pin data connector on adjoining edges of the boards.
The EV system then connects to an IBM-compatible com-
puter running software provided with the MAX191 EV kit.
The following steps outline the procedure for using the
MAX191 EV system:
1) Copy the MAX191 software disk to another disk or
2) Read the README text file found on the floppy disk.
3) Connect the MAX191 evaluation board to the 40-pin
MAX191 Evaluation System/Evaluation Kit
2
DESIGNATION
C8, C9, C11,
C5, C6, C13
C2, C3, C4,
to a hard-disk directory in the personal computer.
Store the original disk in a safe location.
It contains information on any hardware or software
changes made after this manual was written.
data connector on the Maxim 80C32 module.
_______________________________________________________________________________________
C12, C14
QTY
R1, R2
1
1
None
None
None
C10
RS1
C1
C7
U1
U2
U3
U4
H1
J1
EV System Component List
MAX191 evaluation kit (MAX191EVKIT-DIP)
Maxim 80C32 µC module (80C32MODULE-DIP)
QTY
EV System Quick Start
EV Kit Component List
1
6
1
5
1
2
1
1
1
1
1
1
1
1
1
1
200pF ceramic capacitor
10µF 16V electrolytic capacitors
22µF ceramic capacitor
0.1µF ceramic capacitors
0.01µF ceramic capacitor
1kΩ 5% resistors
10kΩ 9-resistor SIP
74HCT157A
Maxim DG413DJ
Maxim ICL7660CPA
Maxim MAX191BCNG
10-pin header
Female data connector
Software on 5 1/4" floppy disk
3.00" x 3.00" PC board
MAX191 data sheet
DESCRIPTION
DESCRIPTION
4) Connect an 8V to 16V source to the 2-pin power
5) Connect a cable from the personal computer to the
6) Turn on the power to the 80C32 module. The switch
7) To start the Maxim EV system software on the per-
8) Set the active serial port, shown on the bottom line,
9) The 80C32 module will transmit a logon message
10) Enter a “?” to display a menu of available MAX191
11) Connect an analog input across the MAX191 inputs
12) Single conversions are displayed whenever the
connector on the 80C32 module. The positive lead
connects to the terminal marked VIN. The Maxim
80C32 module requires approximately 100mA. The
MAX191 evaluation board draws less than 10mA.
9-pin connector on the 80C32 module. If the serial
port on the personal computer has a standard 9-pin
connector, a straight-through cable is used to
attach the board. Computers with a 25-pin serial
port connector need an adapter or adapter cable
(D25 female to D9 male); both are available at most
computer stores.
is located near the 2-pin power connector. The LED
indicates power from the on-board regulator.
sonal computer, set the default drive or directory to
match the storage location of the Maxim programs,
then enter the program name “191EVKIT”.
to indicate the port connected to the Maxim 80C32
module. The Ctrl-T command toggles the active
port between COM1 and COM2. A list of com-
mands affecting the communications link appears
at the bottom of the screen.
and RAM test results when communications are ini-
tialized. The MAX191 RAM resident program will
then be downloaded automatically. The system is
ready for use when the MAX191 revision banner
appears and the status indication on the bottom
display line changes to “*** READY ***”.
conversion commands. This help list is available
whenever the MAX191 system is ready for use.
(AIN+ and AIN-). The input range is 0V to +4.096V
for unipolar and -2.048V to +2.047V for bipolar
operation.
Enter key is pressed. Continuous conversions are
initialized with a “C” and continue until any key is
pressed.