C8051F330DR Silicon Labs, C8051F330DR Datasheet - Page 68

• Manufacturer Part Number: C8051F330DR
• Description: 8-bit Microcontrollers - MCU 8kB 10ADC
• Manufacturer: Silicon Labs

Specifications of C8051F330DR

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• On-chip Adc: No
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: QFN-20
• Mounting Style: SMD/SMT
• Data Rom Size: 128 B
• Interface Type: I2C, SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• On-chip Dac: No
• Processor Series: C8051
• Program Memory Type: Flash
• Factory Pack Quantity: 1500
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V

9.
The MCU system controller core is the CIP-51 microcontroller. The CIP-51 is fully compatible with the
MCS-51™ instruction set; standard 803x/805x assemblers and compilers can be used to develop soft-
ware. The MCU family has a superset of all the peripherals included with a standard 8051. Included are
four 16-bit counter/timers (see description in
in
Special Function Register (SFR) address space
tion
directly with the analog and digital subsystems providing a complete data acquisition or control-system
solution in a single integrated circuit.
The CIP-51 Microcontroller core implements the standard 8051 organization and peripherals as well as
additional custom peripherals and functions to extend its capability (see Figure 9.1 for a block diagram).
The CIP-51 includes the following features:
Performance
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the stan-
dard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system
clock cycles to execute, and usually have a maximum system clock of 12 MHz. By contrast, the CIP-51
core executes 70% of its instructions in one or two system clock cycles, with no instructions taking more
than eight system clock cycles.
Section
- Fully Compatible with MCS-51 Instruction
- 25 MIPS Peak Throughput with 25 MHz
- 0 to 25 MHz Clock Frequency
14). The CIP-51 also includes on-chip debug hardware (see description in
CIP-51 Microcontroller
Set
Clock
16), an Enhanced SPI (see description in
RESET
CLOCK
STOP
IDLE
Figure 9.1. CIP-51 Block Diagram
ACCUMULATOR
PROGRAM COUNTER (PC)
CONTROL
PSW
PRGM. ADDRESS REG.
LOGIC
POWER CONTROL
PC INCREMENTER
DATA POINTER
REGISTER
BUFFER
TMP1
PIPELINE
Section
ALU
(Section
Rev. 1.7
TMP2
DATA BUS
DATA BUS
D8
D8
D8
18), an enhanced full-duplex UART (see description
Section
A16
D8
D8
D8
D8
B REGISTER
9.2.6), and 17 Port I/O (see description in
REGISTER
INTERFACE
INTERFACE
INTERRUPT
INTERFACE
- 256 Bytes of Internal RAM
- 17 Port I/O
- Extended Interrupt Handler
- Reset Input
- Power Management Modes
ADDRESS
MEMORY
SRAM
BUS
SFR
C8051F330/1/2/3/4/5
17), 256 bytes of internal RAM, 128 byte
MEM_WRITE_DATA
SFR_WRITE_DATA
MEM_READ_DATA
STACK POINTER
(256 X 8)
SFR_READ_DATA
SRAM
MEM_CONTROL
EMULATION_IRQ
MEM_ADDRESS
SFR_CONTROL
SFR_ADDRESS
SYSTEM_IRQs
Section
20), and interfaces
Sec-
71