C8051F330DR Silicon Labs, C8051F330DR Datasheet - Page 64

no-image

C8051F330DR

Manufacturer Part Number
C8051F330DR
Description
8-bit Microcontrollers - MCU 8kB 10ADC
Manufacturer
Silicon Labs
Datasheet

Specifications of C8051F330DR

Product Category
8-bit Microcontrollers - MCU
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
8 KB
Data Ram Size
768 B
On-chip Adc
No
Operating Supply Voltage
2.7 V to 3.6 V
Package / Case
QFN-20
Mounting Style
SMD/SMT
Data Rom Size
128 B
Interface Type
I2C, SPI, UART
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
17
Number Of Timers
4
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
1500
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
logic 1 upon a Comparator falling-edge occurrence, and the CP0RIF flag is set to logic 1 upon the Com-
parator rising-edge occurrence. Once set, these bits remain set until cleared by software. The Comparator
rising-edge interrupt mask is enabled by setting CP0RIE to a logic 1. The Comparator0 falling-edge inter-
rupt mask is enabled by setting CP0FIE to a logic 1.
The output state of the Comparator can be obtained at any time by reading the CP0OUT bit. The Compar-
ator is enabled by setting the CP0EN bit to logic 1, and is disabled by clearing this bit to logic 0.
Note that false rising edges and falling edges can be detected when the comparator is first powered on or
if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the
rising-edge and falling-edge flags be explicitly cleared to logic 0 a short time after the comparator is
enabled or its mode bits have been changed. This Power Up Time is specified in Table 8.1 on page 70.
Bit7:
Bit6:
Bit5:
Bit4:
Bits3–2: CP0HYP1–0: Comparator0 Positive Hysteresis Control Bits.
Bits1–0: CP0HYN1–0: Comparator0 Negative Hysteresis Control Bits.
CP0EN
R/W
Bit7
CP0EN: Comparator0 Enable Bit.
0: Comparator0 Disabled.
1: Comparator0 Enabled.
CP0OUT: Comparator0 Output State Flag.
0: Voltage on CP0+ < CP0–.
1: Voltage on CP0+ > CP0–.
CP0RIF: Comparator0 Rising-Edge Flag. Must be cleared by software.
0: No Comparator0 Rising Edge has occurred since this flag was last cleared.
1: Comparator0 Rising Edge has occurred.
CP0FIF: Comparator0 Falling-Edge Flag. Must be cleared by software.
0: No Comparator0 Falling-Edge has occurred since this flag was last cleared.
1: Comparator0 Falling-Edge has occurred.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
CP0OUT
Bit6
R
SFR Definition 8.1. CPT0CN: Comparator0 Control
CP0RIF
R/W
Bit5
CP0FIF CP0HYP1 CP0HYP0 CP0HYN1 CP0HYN0 00000000
R/W
Bit4
Rev. 1.7
R/W
Bit3
R/W
Bit2
C8051F330/1/2/3/4/5
R/W
Bit1
R/W
Bit0
SFR Address:
Reset Value
0x9B
67

Related parts for C8051F330DR