C8051F330DR Silicon Labs, C8051F330DR Datasheet - Page 167

no-image

C8051F330DR

Manufacturer Part Number
C8051F330DR
Description
8-bit Microcontrollers - MCU 8kB 10ADC
Manufacturer
Silicon Labs
Datasheet

Specifications of C8051F330DR

Product Category
8-bit Microcontrollers - MCU
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
8 KB
Data Ram Size
768 B
On-chip Adc
No
Operating Supply Voltage
2.7 V to 3.6 V
Package / Case
QFN-20
Mounting Style
SMD/SMT
Data Rom Size
128 B
Interface Type
I2C, SPI, UART
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
17
Number Of Timers
4
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
1500
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Bits 3 – 2: NSSMD1 – NSSMD0: Slave Select Mode.
Bit 1:
Bit 0:
SPIF
R/W
Bit7
SPIF: SPI0 Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If interrupts are enabled,
setting this bit causes the CPU to vector to the SPI0 interrupt service routine. This bit is not
automatically cleared by hardware. It must be cleared by software.
WCOL: Write Collision Flag.
This bit is set to logic 1 by hardware if a write to SPI0DAT is attempted when the transmit
buffer has not been emptied to the SPI shift register. It must be cleared by software.
MODF: Mode Fault Flag.
This bit is set to logic 1 by hardware (and generates a SPI0 interrupt) when a master mode
collision is detected (NSS is low, MSTEN = 1, and NSSMD[1:0] = 01). This bit is not auto-
matically cleared by hardware. It must be cleared by software.
RXOVRN: Receive Overrun Flag (Slave Mode only).
This bit is set to logic 1 by hardware (and generates a SPI0 interrupt) when the receive buf-
fer still holds unread data from a previous transfer and the last bit of the current transfer is
shifted into the SPI0 shift register. This bit is not automatically cleared by hardware. It must
be cleared by software.
Selects between the following NSS operation modes:
(See
Slave Mode Operation” on page 167
00: 3-Wire Slave or 3-wire Master Mode. NSS signal is not routed to a port pin.
01: 4-Wire Slave or Multi-Master Mode (Default). NSS is always an input to the device.
1x: 4-Wire Single-Master Mode. NSS signal is mapped as an output from the device and will
assume the value of NSSMD0.
TXBMT: Transmit Buffer Empty.
This bit will be set to logic 0 when new data has been written to the transmit buffer. When
data in the transmit buffer is transferred to the SPI shift register, this bit will be set to logic 1,
indicating that it is safe to write a new byte to the transmit buffer.
SPIEN: SPI0 Enable.
This bit enables/disables the SPI.
0: SPI disabled.
1: SPI enabled.
WCOL
R/W
Bit6
Section “17.2. SPI0 Master Mode Operation” on page 165
SFR Definition 17.2. SPI0CN: SPI0 Control
MODF
R/W
Bit5
RXOVRN NSSMD1 NSSMD0
R/W
Bit4
Rev. 1.7
).
R/W
Bit3
R/W
Bit2
C8051F330/1/2/3/4/5
TXBMT
Bit1
R
and
SFR Address: 0xF8
Section “17.3. SPI0
SPIEN
R/W
Bit0
00000110
Addressable
Reset Value
Bit
171

Related parts for C8051F330DR