ZLF645E0H2864G00TR Maxim Integrated, ZLF645E0H2864G00TR Datasheet - Page 61
ZLF645E0H2864G00TR
Manufacturer Part Number
ZLF645E0H2864G00TR
Description
8-bit Microcontrollers - MCU Crimzon Flash Infrared MCU
Manufacturer
Maxim Integrated
Datasheet
1.ZLF645E0H4864G2204.pdf
(201 pages)
Specifications of ZLF645E0H2864G00TR
Core
Z8
Data Bus Width
8 bit
Maximum Clock Frequency
8 MHz
Program Memory Size
64 KB
Data Ram Size
1 KB
Operating Supply Voltage
2 V to 3.6 V
Package / Case
SSOP-28
Mounting Style
SMD/SMT
Interface Type
UART
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Number Of Programmable I/os
5
Number Of Timers
2 x 8 bit, 1 x 16 bit
Processor Series
ZLF645
Program Memory Type
Flash
- Current page: 61 of 201
- Download datasheet (2Mb)
ICP Interface
Enabling ICP Mode
19-4572; Rev 0; 4/09
State of ZLF645 in ICP Mode
The ICP interface of the ZLF645 is a single pin RS-232 like interface for performing
programming, reads, and memory erasures to the ZLF645’s Flash memory. For enabling
the ZLF645 into ICP mode and for performing ICP operations, the ZLF645’s P34 pin
which normally functions as an output only is used.
As mentioned previously, the ZLF645’s GPIO pin P34 is multi-functioned to be used for
putting the ZLF645 into ICP mode and for ICP communications once it is in that mode.
Entry into ICP mode takes place during the ZLF645’s power on reset period. During the
ZLF645’s power on reset period, the P34 pin which normally is an output only pin is
configured by the ZLF645 as an input with pull-up enabled. If during this time this pin is
driven LOW and held LOW until the end of the power on reset period, the ZLF645 will be
put into ICP mode. Once in ICP mode, the P34 pin operates as an open-drain output
bidirectional pin with pull-up enabled. The power on reset period as can be seen from the
electrical specs section of this document can have a duration range of between 2.5 ms and
10 ms. To ensure proper entry into ICP mode, the P34 pin should be driven LOW and held
low a minimum of 10 ms after power up.
If during the ZLF645’s power on reset period, the P34 pin is never driven LOW, pin p34
will be pulled HIGH through its pull-up device. In this case, if P34 remains HIGH until the
end of the power on reset period, the ZLF645 will go into normal user mode and P34 will
revert back to being an output pin only. To ensure proper entry into user mode when it is
not intended to put the ZLF645 into ICP mode, it is important that in the customer
application P34 only be connected to capacitive loads. This is due to the weak nature of its
pull-up device, which can have a resistance ranging between 100 k up to 600 k
depending on voltage, temperature, and process.
The operating characteristics of the device in ICP mode are:
•
•
•
•
The CPU stops executing instructions.
All on-chip peripherals are disabled.
The ZLF645 constantly refreshes the Watchdog Timer, if enabled.
The P34 pin is configured as a bidirectional pin with pull-up enabled and with the
output stage configured as open-drain. The bidirectional control of the pins comes from
the ICP Tx/Rx logic.
ZLF645 Series Flash MCUs
Product Specification
ICP Interface
53
Related parts for ZLF645E0H2864G00TR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: