MAX98090BEWJ+T Maxim Integrated, MAX98090BEWJ+T Datasheet - Page 162
MAX98090BEWJ+T
Manufacturer Part Number
MAX98090BEWJ+T
Description
Interface - CODECs 5V 130mW Stereo Headphone Amp
Manufacturer
Maxim Integrated
Datasheet
1.MAX98090BETL.pdf
(166 pages)
- Current page: 162 of 166
- Download datasheet (13Mb)
MAX98090
EMI Considerations and Optional
Ferrite Bead Filter
Reducing trace length minimizes radiated EMI. On the
PCB, route SPKLP/SPKLN and SPKRP/SPKRN as differ-
ential pairs with the shortest trace lengths possible. This
minimizes trace loop area, and thereby, the inductance of
the circuit. If filter components are used on the speaker
outputs, minimize the trace length from any ground tied
passive components to SPK_GND to further minimize
radiated EMI.
In applications where speaker leads/wires are long
(exceeding approximately 12in), additional EMI suppres-
sion can be achieved by using a filter constructed from a
ferrite bead and a capacitor to ground (Figure 55). Use
a ferrite bead with low DC resistance, high frequency (>
600MHz) impedance between 100Ω and 600Ω, and rated
for at least 1A. The capacitor value varies based on the
ferrite bead chosen and the actual speaker lead length.
Select a capacitor less than 1nF with the value based
upon optimizing EMI performance.
RF Susceptibility
GSM radios transmit using time-division multiple access
(TDMA) with 217Hz intervals. The result is an RF signal
with strong amplitude modulation at 217Hz and its har-
monics that is easily demodulated by audio amplifiers.
The device is designed specifically to reject RF signals;
however, PCB layout has a large impact on the suscepti-
bility of the end product.
In RF applications, improvements to both layout and
component selection decreases the susceptibility to RF
noise and prevent RF signals from being demodulated
into audible noise. Trace lengths should be kept below
1/4 of the wavelength of the RF frequency of interest.
Minimizing the trace lengths prevents them from function-
ing as antennas and coupling RF signals into the device.
The wavelength (λ) in meters is given by: λ = c/f, where c
= 3 x 10
Route audio signals on middle layers of the PCB to allow
ground planes above and below to shield them from RF
interference. Ideally the top and bottom layers of the PCB
should primarily be ground planes to create effective
shielding.
www.maximintegrated.com
8
m/s, and f = the RF frequency of interest.
Figure 55. Optional Class D Ferrite Bead Filter
Figure 56. Optional Class H Output Filter
Additional RF immunity can also be obtained by relying on
the self-resonant frequency of capacitors, as it exhibits a
frequency response similar to a notch filter. Depending on
the manufacturer, 10pF to 20pF capacitors typically exhib-
it self-resonance at RF frequencies. These capacitors,
when placed at the input pins, can effectively shunt the
RF noise at the inputs of the device. For these capacitors
to be effective, they must have a low-impedance, low-
inductance path to the ground plane. Avoid using micro
vias to connect to the ground plane as these vias do
not conduct well at RF frequencies. At the Headphone
outputs, additional RFI can be achieved by using ferrite
beads with the capacitors to ground (Figure 56).
Ultra-Low Power Stereo Audio Codec
MAX98090
MAX98090
JACKSNS
HPSNS
SPK_N
SPK_P
HPR
HPL
Maxim Integrated │ 162
Related parts for MAX98090BEWJ+T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: