MAX98090BEWJ+T Maxim Integrated, MAX98090BEWJ+T Datasheet - Page 122
MAX98090BEWJ+T
Manufacturer Part Number
MAX98090BEWJ+T
Description
Interface - CODECs 5V 130mW Stereo Headphone Amp
Manufacturer
Maxim Integrated
Datasheet
1.MAX98090BETL.pdf
(166 pages)
- Current page: 122 of 166
- Download datasheet (13Mb)
MAX98090
Figure 30. DRC Attack and Release Time Waveforms
The DRC provides a wide range of programmable attack
and release times (Table 53). When the compression
is enabled and the signal amplitude increases until the
compression threshold is exceeded, the attack time
determines how quickly the selected compression ratio
is applied. When the signal amplitude decreases and the
compression threshold would no longer be exceeded, the
release time determines how quickly the gain returns to
normal (Figure 30).
When expansion is enabled and the signal amplitude
decreases until it drops below the expansion threshold,
the release time determines how quickly the selected
expansion ratio is applied. When the signal amplitude
increases and the expansion threshold would no longer
be exceeded, the attack time determines how quickly the
gain returns to normal.
The attack and release times are not absolute. They are
instead used to set the rate at which the gain is adjusted
once the signal amplitude is either above or below the
appropriate threshold. Therefore the selected attack/
release times are relative to the ratio of the new signal
amplitude to the selected compression and expansion
thresholds. The values provided in Table 53 all assume
the input signal amplitude changed to exceed the appro-
priate threshold by a ratio of 12dB (above for compression
www.maximintegrated.com
COMPRESSION
THRESHOLD
AMPLITUDE
INCREASES
COMPRESSION ATTACK TIME (2:1)
COMPRESSED
ATTACK
TIME
AMPLITUDE
and below for expansion). If the appropriate threshold
is exceeded by a larger or smaller ratio, the attack time
is increased or decreased appropriately. The change is
proportional to the change in ratio in dB. For example,
release time is reduced by 50% for 6dB.
For compression, if the signal amplitude exceeds the
threshold by 12dB, the attack time when entering com-
pression precisely matches the selected configuration.
Likewise, when exiting compression, the release time
is determined by the ratio by which the threshold was
exceeded prior to the amplitude dropping.
Expansion works in exactly the same fashion except for
two differences. The expansion ratio is applied when the
signal amplitude drops below the expansion threshold
(rather than above for compression), and the release time
(rather than attack time) determines how long it takes to
enter expansion (centered at 12dB below the expansion
threshold). Likewise, the attack time is then used when
exiting expansion. In addition, when entering expansion,
the ratio of the initial input amplitude to the expansion
threshold sets a delay before the expansion ratio is
applied. This delay is centered at 12dB above the expan-
sion threshold and is determined by the selected release
time. There is no delay prior to the attack time when exit-
ing expansion.
Ultra-Low Power Stereo Audio Codec
COMPRESSION RELEASE TIME (2:1)
RELEASED AMPLITUDE
COMPRESSED AMPLITUDE
AMPLITUDE
DECECREASES
RELEASE
TIME
Maxim Integrated │ 122
Related parts for MAX98090BEWJ+T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: