PIC18F2420-I/SOC01 Microchip, PIC18F2420-I/SOC01 Datasheet - Page 44
PIC18F2420-I/SOC01
Manufacturer Part Number
PIC18F2420-I/SOC01
Description
28 pin, 16 kb flash, 3804 ram, 25 i/o...
Manufacturer
Microchip
Datasheet
1.PIC18F2420-ISOC01.pdf
(412 pages)
- Current page: 44 of 412
- Download datasheet (7Mb)
PIC18F2420/2520/4420/4520
REGISTER 4-1:
DS39631E-page 42
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent
R/W-0
IPEN
2:
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to
If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’.
The actual Reset value of POR is determined by the type of device Reset. See the notes following this
register and Section 4.6 “Reset State of Registers” for additional information.
Power-on Resets may be detected.
‘1’ by software immediately after a Power-on Reset).
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN1:BOREN0 = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN1:BOREN0 = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after a
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-Down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
SBOREN
R/W-1
Brown-out Reset occurs)
RCON: RESET CONTROL REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
U-0
—
R/W-1
RI
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-1
TO
R-1
PD
© 2008 Microchip Technology Inc.
x = Bit is unknown
R/W-0
POR
(2)
R/W-0
BOR
bit 0
Related parts for PIC18F2420-I/SOC01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28-DIP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28 PIN, 16 KB STD FLASH, 3804 RAM, 25 I/O, PB FREE,
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40-Pin High-Performance, Enhanced Flash Microcontrollers with CAN Module
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC30F 80QFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN 18F87J50 FS USB
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
BOARD DAUGHTER USB PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC33F 100TQFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
CARD DAUGHTER AUDIO PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet: