PIC18F2420-I/SOC01 Microchip, PIC18F2420-I/SOC01 Datasheet - Page 191
PIC18F2420-I/SOC01
Manufacturer Part Number
PIC18F2420-I/SOC01
Description
28 pin, 16 kb flash, 3804 ram, 25 i/o...
Manufacturer
Microchip
Datasheet
1.PIC18F2420-ISOC01.pdf
(412 pages)
- Current page: 191 of 412
- Download datasheet (7Mb)
17.4.8
To initiate a Start condition, the user sets the Start
Enable bit, SEN (SSPCON2<0>). If the SDA and SCL
pins are sampled high, the Baud Rate Generator is
reloaded with the contents of SSPADD<6:0> and starts
its count. If SCL and SDA are both sampled high when
the Baud Rate Generator times out (T
pin is driven low. The action of the SDA being driven
low while SCL is high is the Start condition and causes
the S bit (SSPSTAT<3>) to be set. Following this, the
Baud Rate Generator is reloaded with the contents of
SSPADD<6:0> and resumes its count. When the Baud
Rate Generator times out (T
(SSPCON2<0>) will be automatically cleared by
hardware; the Baud Rate Generator is suspended,
leaving the SDA line held low and the Start condition is
complete.
FIGURE 17-19:
© 2008 Microchip Technology Inc.
I
CONDITION TIMING
2
C MASTER MODE START
Write to SEN bit occurs here
FIRST START BIT TIMING
SDA
SCL
BRG
), the SEN bit
BRG
), the SDA
PIC18F2420/2520/4420/4520
SDA = 1,
SCL = 1
T
BRG
Set S bit (SSPSTAT<3>)
T
S
BRG
At completion of Start bit,
hardware clears SEN bit
17.4.8.1
If the user writes the SSPBUF when a Start sequence
is in progress, the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
and sets SSPIF bit
Note:
Note:
T
Write to SSPBUF occurs here
BRG
1st bit
If, at the beginning of the Start condition,
the SDA and SCL pins are already sam-
pled low, or if during the Start condition, the
SCL line is sampled low before the SDA
line is driven low, a bus collision occurs,
the Bus Collision Interrupt Flag, BCLIF, is
set, the Start condition is aborted and the
I
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
2
C module is reset into its Idle state.
WCOL Status Flag
T
BRG
2nd bit
DS39631E-page 189
Related parts for PIC18F2420-I/SOC01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28-DIP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28 PIN, 16 KB STD FLASH, 3804 RAM, 25 I/O, PB FREE,
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40-Pin High-Performance, Enhanced Flash Microcontrollers with CAN Module
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC30F 80QFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN 18F87J50 FS USB
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
BOARD DAUGHTER USB PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC33F 100TQFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
CARD DAUGHTER AUDIO PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet: