PIC18F2420-I/SOC01 Microchip, PIC18F2420-I/SOC01 Datasheet - Page 167
PIC18F2420-I/SOC01
Manufacturer Part Number
PIC18F2420-I/SOC01
Description
28 pin, 16 kb flash, 3804 ram, 25 i/o...
Manufacturer
Microchip
Datasheet
1.PIC18F2420-ISOC01.pdf
(412 pages)
- Current page: 167 of 412
- Download datasheet (7Mb)
17.3.3
To enable the serial port, MSSP Enable bit, SSPEN
(SSPCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, reinitialize the
SSPCON registers and then set the SSPEN bit. This
configures the SDI, SDO, SCK and SS pins as serial
port pins. For the pins to behave as the serial port func-
tion, some must have their data direction bits (in the
TRIS register) appropriately programmed as follows:
• SDI is automatically controlled by the SPI module
• SDO must have TRISC<5> bit cleared
• SCK (Master mode) must have TRISC<3> bit
• SCK (Slave mode) must have TRISC<3> bit set
• SS must have TRISA<5> bit set
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.
FIGURE 17-2:
© 2008 Microchip Technology Inc.
cleared
ENABLING SPI I/O
SPI Master SSPM<3:0> = 00xxb
MSb
PROCESSOR 1
Serial Input Buffer
SPI MASTER/SLAVE CONNECTION
Shift Register
(SSPBUF)
(SSPSR)
LSb
SDO
SCK
SDI
PIC18F2420/2520/4420/4520
Serial Clock
17.3.4
Figure 17-2 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data – Slave sends dummy data
• Master sends data – Slave sends data
• Master sends dummy data – Slave sends data
SDO
SCK
SDI
TYPICAL CONNECTION
SPI Slave SSPM<3:0> = 010xb
MSb
Serial Input Buffer
Shift Register
PROCESSOR 2
(SSPBUF)
(SSPSR)
LSb
DS39631E-page 165
Related parts for PIC18F2420-I/SOC01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
IC MCU FLASH 8KX16 28-DIP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC PIC MCU FLASH 8KX16 28QFN
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28 PIN, 16 KB STD FLASH, 3804 RAM, 25 I/O, PB FREE,
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
28/40-Pin High-Performance, Enhanced Flash Microcontrollers with CAN Module
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC30F 80QFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN 18F87J50 FS USB
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
BOARD DAUGHTER USB PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
MODULE PLUG-IN DSPIC33F 100TQFP
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
CARD DAUGHTER AUDIO PICTAIL PLUS
Manufacturer:
Microchip Technology
Datasheet: