M27C4001-90XN1X STMicroelectronics, M27C4001-90XN1X Datasheet
M27C4001-90XN1X
Related parts for M27C4001-90XN1X
M27C4001-90XN1X Summary of contents
Page 1
... ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: 41h DESCRIPTION The M27C4001 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable ideally suited for micro- processor systems requiring large programs and is organised as 524,288 by 8 bits. ...
Page 2
... The M27C4001 has a standby mode which reduc the supply current from 30mA to 100 A. The M27C4001 is placed in the standby mode by ap- plying a CMOS high signal to the E input. When in the standby mode, the outputs are in a high imped- ance state, independent of the G input. ...
Page 3
... READ line from the system control bus. This ensures that all deselect- ed memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device. M27C4001 Value Unit –40 to 125 C –50 to 125 C – ...
Page 4
... M27C4001 Table 5. AC Measurement Conditions Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages Figure 3. Testing Input Output Waveform High Speed 3V 0V Standard 2.4V 0.4V (1) Table 6. Capacitance ( MHz) A Symbol Parameter C Input Capacitance IN C Output Capacitance OUT Note: 1 ...
Page 5
... Test Condit ion -35 Min Max and removed simultaneously or after V PP M27C4001 ) Min Max Unit 100 –0.3 0 0 – ...
Page 6
... Q0-Q7 Programming When delivered (and after each erasure for UV EPROM), all bits of the M27C4001 are in the ’1’ state. Data is introduced by selectively program- ming ’0’s into the desired bit locations. Although only ’0’s will be programmed, both ’1’s and ’0’s can be present in the data word ...
Page 7
... Sampled only, not 100% tested. (1) = 12.75V 0.25V) PP Test Conditio 2.1mA –400 A OH and removed simultaneously or after V PP (1) = 12.75V 0.25V) PP Test Condition and removed simultaneously or after V PP M27C4001 Min Max Unit –0 0.4 V 2.4 V 11.5 12 Min ...
Page 8
... M27C4001 8/16 PRESTO II Programming Algorithm PRESTO II Programming Algorithm allows the whole array to be programmed with a guaranteed margin typical time of 52.5 seconds. Pro- gramming with PRESTO II consists of applying a sequence of 100 s program pulses to each byte until a correct verify occurs (see Figure 7). During programming and verify operation, a MARGIN ...
Page 9
... M27C4001 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27C4001 exposed am- these types of lighting conditions for extended pe- riods of time suggested that opaque labels be put over the M27C4001 window to prevent unin- tentional erasure ...
Page 10
... Optio Additional Burn-in TR =Tape & Reel Packing Note: 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the ST Sales Office nearest to you. 10/16 M27C4001 - ...
Page 11
... M27C4001 inches Min Max 0.225 0.020 0.055 0.154 0.180 0.153 0.177 0.016 0.022 – – 0.009 0.012 1.643 1.655 – – – – 0.514 0.526 – ...
Page 12
... M27C4001 Table 13. PDIP32 - 32 lead Plastic DIP, 600 mils width, Package Mechanical Data Symb Typ 1. 41.78 D2 38.10 E 15.24 E1 13.59 e1 2.54 eA 15.24 eB 15. Figure 9. PDIP32 - 32 lead Plastic DIP, 600 mils width, Package Outline Drawing is not to scale. 12/16 mm Min Max Typ – ...
Page 13
... A M27C4001 inches Min Max 0.110 0.020 0.028 0.442 0.458 0.540 0.560 – – 0.015 – – – – – – – – – 0.045 0.055 0.077 ...
Page 14
... M27C4001 Table 15. PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular, Package Mechanical Data Symb Typ 12.32 D1 11. 14.86 E1 13.89 E2 12. Figure 11. PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular, Package Outline PLCC Drawing is not to scale. 14/16 mm Min ...
Page 15
... TSOP-a Drawing is not to scale. mm Min Max Typ 1.20 0.05 0.17 0.95 1.05 0.15 0.27 0.10 0.21 20.20 18.50 7.90 8.10 – – 0.020 0. M27C4001 inches Min Max 0.047 0.002 0.006 0.037 0.041 0.006 0.011 0.004 0.008 0.780 0.795 0.720 0.728 0.311 0.319 – – 0.020 0.028 0.004 15/16 ...
Page 16
... M27C4001 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice ...