HD6433935 Hitachi, HD6433935 Datasheet - Page 242
HD6433935
Manufacturer Part Number
HD6433935
Description
8-Bit MICROCONTROLLER
Manufacturer
Hitachi
Datasheet
1.HD6433935.pdf
(521 pages)
- Current page: 242 of 521
- Download datasheet (2Mb)
Table 9-15 Input Capture Input Signal Input Edges Due to Input Capture Input Pin
Input Capture Input
Signal Input Edge
Generation of rising edge
Generation of falling edge
Note: When the P1
When performing noise canceler function switching by modifying NCS in port mode register 3
(PMR3), which controls the input capture input noise canceler, TMIG should first be cleared to 0.
Note that if NCS is modified without first clearing TMIG, an edge will be regarded as having been
input at the pin even though no valid edge has actually been input. Input capture input signal input
edges, and the conditions for their occurrence, are summarized in table 9-16.
Table 9-16 Input Capture Input Signal Input Edges Due to Noise Canceler Function
Input Capture Input
Signal Input Edge
Generation of rising edge
Generation of falling edge
230
Switching input capture input noise canceler function
signal is low.
Switching, and Conditions for Their Occurrence
Switching, and Conditions for Their Occurrence
3
pin is not set as an input capture input pin, the timer G input capture input
Conditions
When TMIG is modified from 0 to 1 while the TMIG pin is high
When NCS is modified from 0 to 1 while the TMIG pin is high, then
TMIG is modified from 0 to 1 before the signal is sampled five times by
the noise canceler
When TMIG is modified from 1 to 0 while the TMIG pin is high
When NCS is modified from 0 to 1 while the TMIG pin is low, then
TMIG is modified from 0 to 1 before the signal is sampled five times by
the noise canceler
When NCS is modified from 0 to 1 while the TMIG pin is high, then
TMIG is modified from 1 to 0 after the signal is sampled five times by
the noise canceler
Conditions
When the TMIG pin level is switched from low to high while TMIG is
set to 1, then NCS is modified from 0 to 1 before the signal is sampled
five times by the noise canceler
When the TMIG pin level is switched from high to low while TMIG is
set to 1, then NCS is modified from 1 to 0 before the signal is sampled
five times by the noise canceler
Related parts for HD6433935
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: