MC9S08GT16 MOTOROLA [Motorola, Inc], MC9S08GT16 Datasheet - Page 197
![no-image](/images/no-image-200.jpg)
MC9S08GT16
Manufacturer Part Number
MC9S08GT16
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC9S08GT16.pdf
(290 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC9S08GT16ACBE
Manufacturer:
SHARP
Quantity:
1 200
Company:
Part Number:
MC9S08GT16ACFBE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S08GT16ACFBER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S08GT16ACFBER
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
MC9S08GT16AMFBE
Manufacturer:
XILINX
Quantity:
1 300
Company:
Part Number:
MC9S08GT16AMFBE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S08GT16CFBE
Manufacturer:
FREESCALE
Quantity:
1 831
Part Number:
MC9S08GT16CFBE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC9S08GT16CFD
Manufacturer:
FREESCALE
Quantity:
20 000
12.4.1
This read/write register includes the SPI enable control, interrupt enables, and configuration options.
SPIE — SPI Interrupt Enable (for SPRF and MODF)
SPE — SPI System Enable
SPTIE — SPI Transmit Interrupt Enable
MSTR — Master/Slave Mode Select
CPOL — Clock Polarity
CPHA — Clock Phase
Freescale Semiconductor
This is the interrupt enable for SPI receive buffer full (SPRF) and mode fault (MODF) events.
Disabling the SPI halts any transfer that is in progress, clears data buffers, and initializes internal state
machines. SPRF is cleared and SPTEF is set to indicate the SPI transmit data buffer is empty.
This is the interrupt enable bit for SPI transmit buffer empty (SPTEF).
This bit effectively places an inverter in series with the clock signal from a master SPI or to a slave SPI
device. Refer to
This bit selects one of two clock formats for different kinds of synchronous serial peripheral devices.
Refer to
1 = When SPRF or MODF is 1, request a hardware interrupt.
0 = Interrupts from SPRF and MODF inhibited (use polling).
1 = SPI system enabled.
0 = SPI system inactive.
1 = When SPTEF is 1, hardware interrupt requested.
0 = Interrupts from SPTEF inhibited (use polling).
1 = SPI module configured as a master SPI device.
0 = SPI module configured as a slave SPI device.
1 = Active-low SPI clock (idles high).
0 = Active-high SPI clock (idles low).
1 = First edge on SPSCK occurs at the start of the first cycle of an 8-cycle data transfer.
0 = First edge on SPSCK occurs at the middle of the first cycle of an 8-cycle data transfer.
SPI Control Register 1 (SPI1C1)
Section 12.3.1, “SPI Clock
Section 12.3.1, “SPI Clock
Reset:
Read:
Write:
SPIE
Bit 7
Figure 12-7. SPI Control Register 1 (SPI1C1)
0
MC9S08GB/GT Data Sheet, Rev. 2.3
SPE
Formats,” for more details.
6
0
SPTIE
Formats,”
5
0
MSTR
for more details.
4
0
CPOL
3
0
CPHA
2
1
SPI Registers and Control Bits
SSOE
1
0
LSBFE
Bit 0
0
197