TNY274G POWERINT [Power Integrations, Inc.], TNY274G Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
TNY274G
Manufacturer Part Number
TNY274G
Description
Energy Efficient, Off-Line Switcher with Enhanced Flexibility and Extended Power Range
Manufacturer
POWERINT [Power Integrations, Inc.]
Datasheet
1.TNY274G.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TNY274GN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
TNY274GN
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
TNY274GN-TL
Manufacturer:
ST
Quantity:
5 000
Company:
Part Number:
TNY274GN-TL
Manufacturer:
PowerInt
Quantity:
81 000
Part Number:
TNY274GN-TL
Manufacturer:
POWER
Quantity:
20 000
Power Up/Down
The TinySwitch-III requires only a 0.1 µF capacitor on the
BYPASS/MULTI-FUNCTION pin to operate with standard
current limit. Because of its small size, the time to charge this
capacitor is kept to an absolute minimum, typically 0.6 ms. The
time to charge will vary in proportion to the BYPASS/MULTI-
FUNCTION pin capacitor value when selecting different current
limits. Due to the high bandwidth of the ON/OFF feedback,
there is no overshoot at the power supply output. When an
external resistor (4 MΩ) is connected from the positive DC
input to the EN/UV pin, the power MOSFET switching will
be delayed during power-up until the DC line voltage exceeds
the threshold (100 V). Figures 10 and 11 show the power-up
timing waveform in applications with and without an external
resistor (4 MΩ) connected to the EN/UV pin.
Under startup and overload conditions, when the conduction time
is less than 400 ns, the device reduces the switching frequency
to maintain control of the peak drain current.
During power-down, when an external resistor is used, the
power MOSFET will switch for 64 ms after the output loses
regulation. The power MOSFET will then remain off without
any glitches since the under-voltage function prohibits restart
when the line voltage is low.
Figure 12 illustrates a typical power-down timing waveform.
Figure 13 illustrates a very slow power-down timing waveform
as in standby applications. The external resistor (4 MΩ) is
connected to the EN/UV pin in this case to prevent unwanted
restarts.
No bias winding is needed to provide power to the chip
because it draws the power directly from the DRAIN pin (see
Functional Description above). This has two main benefits.
First, for a nominal application, this eliminates the cost of a
bias winding and associated components. Secondly, for battery
charger applications, the current-voltage characteristic often
allows the output voltage to fall close to zero volts while still
delivering power. TinySwitch-III accomplishes this without a
forward bias winding and its many associated components. For
applications that require very low no-load power consumption
(50 mW), a resistor from a bias winding to the BYPASS/
MULTI-FUNCTION pin can provide the power to the chip.
The minimum recommended current supplied is 1 mA. The
BYPASS/MULTI-FUNCTION pin in this case will be clamped
at 6.4 V. This method will eliminate the power draw from the
DRAIN pin, thereby reducing the no-load power consumption
and improving full-load efficiency.
Current Limit Operation
Each switching cycle is terminated when the DRAIN current
reaches the current limit of the device. Current limit operation
provides good line ripple rejection and relatively constant power
delivery independent of input voltage.
BYPASS/MULTI-FUNCTION Pin Capacitor
The BYPASS/MULTI-FUNCTION pin can use a ceramic
capacitor as small as 0.1 µF for decoupling the internal power
supply of the device. A larger capacitor size can be used to adjust
the current limit. For TNY275-280, a 1 µF BP/M pin capacitor
will select a lower current limit equal to the standard current
limit of the next smaller device and a 10 µF BP/M pin capacitor
will select a higher current limit equal to the standard current
limit of the next larger device. The higher current limit level of
the TNY280 is set to 850 mA typical. The TNY274 MOSFET
does not have the capability for increased current limit so this
feature is not available in this device.
TNY274-280
2/06
E
7