MC34118-D28-T UTC [Unisonic Technologies], MC34118-D28-T Datasheet - Page 2

• Manufacturer Part Number: MC34118-D28-T
• Description: VOICE SWITCHED SPEAKER-PHONE CIRCUIT
• Manufacturer: UTC [Unisonic Technologies]

MC34118
PIN NO
PIN DESCRIPTION
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
2
3
4
5
6
7
8
9
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
PIN NAME
HTO+
TLO2
RLO2
TLO1
RLO1
HTO-
MCO
MUT
RXO
GND
TXO
CPT
TLI2
RLI2
TLI1
RLI1
CPR
VLC
MCI
V
HTI
RXI
TXI
FO
CD
CT
VB
FI
CC
Output of filter. The output impedance is less than 50Ω.
Input of filter. The input impedance is less than 1MΩ.
Chip Disable input .A logic low (voltage lower than 0.8V) sets normal operation. A logic
high (voltage higher than 2V) disable the IC. This pin’s input impedance is 90 KΩ
nominally.
This pin requires a supply voltage of +2.8V ~ +6.5V at 5mA. After V
2.8V, when in the receive mode, an AGC circuit reduces the receive attenuator gain by
25dB.
The output of the second hybrid amplifier. This amplifier’s gain is internally set at -1.
Output of the first hybrid amplifier. This amplifier’s gain of the amplifier is set by
external resistors.
The first hybrid amplifier’s input and summing node. DC level is about equal to VB.
The transmit attenuator’s output. DC level is about VB.
The transmit attenuator’s input. It’s maximum signal level is 350 mVrms. The input
impedance is 10KΩ.
The microphone amplifier’s output. This amplifier’s gain is set by external resistors.
The summing node of the microphone’s input. DC lever is VB.
Input of mute. A logic low (voltage lower than 0.8V) sets the circuit normal operation. A
logic high (voltage higher than 2V) mutes the microphone amplifier, but it doesn’t affect
the rest of the circuit. The input impedance is 90 K ohms.
The input of Volume control. In the receive mode, when VLC=VB, the receive
attenuator is at maximum gain. The receive gain is down 35dB when VLC=0.3dB, and
it does not effect the transmit modes.
At this pin, to switch modes, the RC sets the response time for the circuit.
In this pin, there’s an output voltage=Vcc/2 which is a system AC ground and biases
the volume control. What required is a filter capacitor.
The time constant for the transmit background side can be set by the RC at this pin .
The input to the transmit level detector which is on the microphone/ speaker side.
The output to the transmit level detector which is on the microphone/ speaker side.
Also the input to the transmit background monitor.
The Output of the receive level detector which is on the microphone/ speaker side
The input to the receive level detector which is on the microphone/ speaker side
The input to the receive attenuator and dial tone detector. In this pin, the maximum
input level is 350mVrms,and the input impedance is 10KΩ.
The output of the receive attenuator. This pin’s DC level is VB.
The input to the transmit level detector which is on the line side.
The output to the transmit level detector which is on the line side, and also the input to
the transmit background monitor.
The output of the receive level detector which is on the line side.
The input to the receive level detector which is on the line side.
The time constant for the receive background monitor can be set by the RC at this pin.
Ground.
DESCRIPTION
LINEAR INTEGRATED CIRCUIT
CC
falls from 3.5V ~
QW-R108-007,D
2 of 12