LSI53C875 LSI Logic, LSI53C875 Datasheet - Page 45
LSI53C875
Manufacturer Part Number
LSI53C875
Description
PCI to Ultra SCSI I/O Processor
Manufacturer
LSI Logic
Datasheet
1.LSI53C875.pdf
(314 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LSI53C875-160QFP
Manufacturer:
LSI
Quantity:
20 000
Company:
Part Number:
LSI53C875J
Manufacturer:
NS
Quantity:
4 490
Part Number:
LSI53C875J
Manufacturer:
LSILOGIC
Quantity:
20 000
- Current page: 45 of 314
- Download datasheet (3Mb)
To interface the LSI53C875 to the SN75976A, connect the DIR pins, as
well as IGS and TGS, of the LSI53C875 directly to the transceiver
enables (nDE/RE/). These signals control the direction of the channels
on the SN75976A.
The SCSI bidirectional control and data pins (SD[7:0]/, SDP0/, REQ/,
ACK/, MSG/, I_O/, C_D/, and ATN/) of the LSI53C875 connect to the
bidirectional data pins (nA) of the SN75976A with a pull-up resistor. The
pull-up value should be no lower than the transceiver I
but not so high as to cause RC timing problems. The three remaining
pins, SEL/, BSY/, and RST/ are connected to the SN75976A with a
pull-down resistor. The pull-down resistors are required when the pins
(nA) of the SN75976A are configured as inputs. When the data pins are
inputs, the resistors provide a bias voltage to both the LSI53C875 pins
(SEL/, BSY/, and RST/) and the SN75976A data pins. Because the SEL/,
BSY/, and RST/ pins on the LSI53C875 are inputs only, this configuration
allows for the SEL/, BSY/, and RST/ SCSI signals to be asserted on the
SCSI bus. The differential pairs on the SCSI bus are reversed when
connected to the SN75976A, due to the active low nature of the SCSI
bus.
8-Bit/16-Bit SCSI and the Differential Interface – In an 8-bit SCSI
bus, the SD[15:8] pins on the LSI53C875 should be pulled up with a
1.5 k
very important, as errors may occur during reselection if these lines are
left floating. In the LSI53C875J and LSI53C875JB, the SDIRP1 pin is
replaced by the TCK JTAG signal. If the device is used in a wide
differential system, use the SDIRP0 pin to control the direction of the
differential transceiver for both the SP0 and SP1 signals. The SDIRP0
signal is capable of driving both direction inputs from a transceiver.
PCI Cache Mode
Note:
resistor or terminated like the rest of the SCSI bus lines. This is
The SN75976A differential transceiver must be used to
achieve Ultra SCSI transfer rates.
OL
can tolerate,
2-21
Related parts for LSI53C875
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LR33000 Self-Embedding Processor
Manufacturer:
LSI [LSI Computer Systems]
Datasheet:
Part Number:
Description:
LSI for 16 CH Multiplexing
Manufacturer:
Mitsubishi
Datasheet:
Part Number:
Description:
DVD Recorder System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
DVD Recorder System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
Servo / Video Decoder and System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
Mpeg-2 Audio/video Decoder
Manufacturer:
LSI Logic Corporation
Datasheet:
Part Number:
Description:
Satellite Decoder Technical Manual 5/97
Manufacturer:
LSI Logic Corporation
Datasheet:
Part Number:
Description:
Satellite Receiver
Manufacturer:
LSI Logic Corporation
Datasheet: