s3c72m9 Samsung Semiconductor, Inc., s3c72m9 Datasheet - Page 194
s3c72m9
Manufacturer Part Number
s3c72m9
Description
The S3c72m5/s3c72m7/s3c72m9 Single-chip Cmos Microcontroller Has Been Designed For High Performance Using Samsung S
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.S3C72M9.pdf
(382 pages)
- Current page: 194 of 382
- Download datasheet (2Mb)
SAM47 INSTRUCTION SET
VENT —
VENTn
Operation:
Description:
5-90
dst
The VENT instruction loads the contents of the enable memory bank flag (EMB) and enable register
bank flag (ERB) into the respective vector addresses. It then points the interrupt service routine to
the corresponding branching locations. The program counter is loaded automatically with the
respective vector addresses which indicate the starting address of the respective vector interrupt
service routines.
The EMB and ERB flags should be modified using VENT before the vector interrupts are
acknowledged. Then, when an interrupt is generated, the EMB and ERB values of the previous
routine are automatically pushed onto the stack and then popped back when the routine is
completed.
After the return from interrupt (IRET) you do not need to set the EMB and ERB values again.
Instead, use BITR and BITS to clear these values in your program routine.
The starting addresses for vector interrupts and reset operations are pointed to by the VENTn
instruction. These addresses must be stored in ROM locations 0000H–3FFFH. Generally, the
VENTn instructions are coded starting at location 0000H.
The format for VENT instructions is as follows:
EMB
ERB
PC
n = device-specific module address code (n = 0–7)
Load EMB, ERB, and Vector Address
EMB (0,1)
ERB (0,1)
EMB (0,1)
Operand
ERB (0,1)
Operand
ADR
ADR
ADDR (address to branch)
VENTn
d2 ("0" or "1")
d1 ("0" or "1")
Load enable memory bank flag (EMB) and the enable
register bank flag (ERB) and program counter to vector
address, then branch to the corresponding location.
a7
M
E
B
d1,d2,ADDR
a6
E
R
B
a13
a5
Binary Code
Operation Summary
a12
a4
a11 a10
a3
a2
S3C72M5/C72M7/C72M9/P72M9 (Preliminary Spec)
a9
a1
a8
a0
ROM (2 x n) 7–6
ROM (2 x n) 5–4
PC12
ROM (2 x n) 3–0
ROM (2 x n + 1) 7–0
(n = 0, 1, 2, 3, 4, 5, 6, 7)
Operation Notation
Bytes
2
PC12–8
EMB, ERB
0, PC13,
Cycles
PC7–0
2
Related parts for s3c72m9
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Transistor,mosfet,n-channel,200v V Br Dss,5.9a
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Samsung Power Switch
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Samsung Pm410 Ssd 1.8 Lif 128/64gb
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Low Voltage Audio Power Amp
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Dual Equalizer Amplifier With Alc
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Low Dropout Voltage Regulator
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
1 Chip Codec For Digital Answering Phone
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
10/15 Ch Pll
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Flextm Roaming Decoder Ii
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
128k X 8bit Low Power And Low Voltage Cmos Statinc Ram
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Ballast/backlight Controller/driver,sop,20pin,plastic
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
3 Channel R.g.b Video Amplifier
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Rgb Encoder For Pal/ntsc
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
R/g/b Video Amplifier With Osd Interface For Monitors
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Remote Control Preamplifier
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet: