a8286 Allegro MicroSystems, Inc., a8286 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
a8286
Manufacturer Part Number
a8286
Description
Dual Lnb Supply And Control Voltage Regulator
Manufacturer
Allegro MicroSystems, Inc.
Datasheet
1.A8286.pdf
(19 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
a8286SETTR
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
Part Number:
a8286SETTR-T
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
Part Number:
a8286SLB
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
A8286
Tone Generation
The A8286 solution offers four options for tone generation,
providing maximum flexibility to cover every application. The
EXTM pins (external modulation), in conjunction with the I
control bits: TMODE (tone modulation) and TGATE (tone gate),
provide the necessary control. The TMODE bit controls whether
the tone source is either internal or external (via the EXTM pin).
Figure 2. Options for tone generation
Option 1 – Use internal tone, gated by the TGATE bit.
Option 2 – Use internal tone, gated by the EXTM pin.
Option 3 – Use external tone, gated by the TGATE bit.
Option 4 – Use external tone.
TMODE
TMODE
TMODE
TMODE
TGATE
Tone
(LNB Ref)
EXTM
EXTM
TGATE
Tone
(LNB Ref)
EXTM
TGATE
Tone
(LNB Ref)
EXTM
TGATE
Tone
(LNB Ref)
Dual LNB Supply and Control Voltage Regulator
LNB (V)
LNB (V)
LNB (V)
LNB (V)
2
C™
Both the EXTM pin and TGATE bit determine the 22 kHz con-
trol, whether gated or clocked.
that when using option 4, when EXTM stops clocking, the LNB
volts park at the LNB voltage, either plus or minus half the tone
signal amplitude, depending on the state of EXTM. For example,
if the EXTM is held low, the LNB DC voltage is the LNB pro-
grammed voltage minus 325 mV (typical).
TDET is set in the status register. When the internal tone is used
(options 1 or 2), the minimum tone detect amplitude is 400 mV,
and when an external tone is used (options 3 or 4), the minimum
tone detection amplitude is 300 mV.
I
This is a serial interface that uses two bus lines, SCL and SDA,
to access the internal Control and Status registers of the A8286.
Data is exchanged between a microcontroller (master) and the
A8286 (slave). The clock input to SCL is generated by the master,
while SDA functions as either an input or an open drain output,
depending on the direction of the data.
Timing Considerations
The control sequence of the communication through the I
compatible interface is composed of several steps in sequence:
1. Start Condition. Defined by a negative edge on the SDA line,
2. Address Cycle. 7 bits of address, plus 1 bit to indicate read (1)
3. Data Cycles.
4. Stop Condition. Defined by a positive edge on the SDA line,
2
C™-Compatible Interface
while SCL is high.
or write (0), and an acknowledge bit. The first five bits of the
address are fixed as: 00010. The four optional addresses, de-
fined by the remaining two bits, are selected by the ADD input.
The address is transmitted MSB first.
Write – 6 bits of data and 2 bits for addressing four internal
control registers, followed by an acknowledge bit. See Control
Register section for more information.
Read – Two status registers, where register 1 is read first,
followed by register 2, then register 1, and so on. At the start
of any read sequence, register 1 is always read first. Data is
transmitted MSB first.
while SCL is high. Except to indicate a Start or Stop condi-
tion, SDA must be stable while the clock is high. SDA can
only be changed while SCL is low. It is possible for the Start or
Stop condition to occur at any time during a data transfer. The
Four options for tone generation are shown in figure 2. Note
With any of the four options, when a tone signal is generated,
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
2
C™-
9