iru1207 International Rectifier Corp., iru1207 Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/339/international_rectifier_corp__sml.jpg)
iru1207
Manufacturer Part Number
iru1207
Description
1a Very Low Dropout Positive Fixed And Adjustable Regulators -
Manufacturer
International Rectifier Corp.
Datasheet
1.IRU1207.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
iru1207-18CS
Manufacturer:
IR
Quantity:
20 000
Part Number:
iru1207-25CS
Manufacturer:
IR
Quantity:
20 000
Company:
Part Number:
iru1207-33CS
Manufacturer:
AMI
Quantity:
6 254
Part Number:
iru1207-33CS
Manufacturer:
IR
Quantity:
20 000
PARAMETER
IRU1207, IRU1209
Ground Current - SD Activated
Enable Pin Input LO Voltage
Enable Pin Input HI Voltage
Enable Pin Input LO Current
Enable Pin Input HI Current
IRU1207, IRU1208
Flag Output Threshold Voltage
Flag Output Hysteresis Voltage
Flag Output Saturation Voltage
Note 1: Low duty cycle pulse testing with Kelvin con-
nections is required in order to maintain accurate data.
Note 2: Dropout voltage is defined as the minimum dif-
ferential voltage between V
tain regulation at V
voltage drops 1% below its nominal value.
PIN DESCRIPTIONS
APPLICATION INFORMATION
Stability
The IRU120X series of regulators require the use of an
output capacitor as part of the frequency compensation
in order to make the regulator stable. A minimum of 2.2mF
capacitance and the ESR in the range of 0.5 to 2V in-
sures the stability of the system.
Rev. 2.3
08/02/02
(IRU1207, IRU1209)
(IRU1207, IRU1208)
(IRU1208, IRU1209)
PIN SYMBOL
(All devices)
(All devices)
(All devices)
Enable
V
Gnd
Flag
Adj
V
OUT
IN
OUT
. It is measured when the output
The input pin of the regulator. Typically a large storage capacitor is connected from this pin
to ground to insure that the input voltage does not sag below the minimum drop out voltage
during the load transient response. This pin must always be 0.6V higher than V
for the device to regulate properly.
The output of the regulator. A minimum of 2.2mF capacitor must be connected from this pin
to ground.
Ground pin. This pin must be connected to the lowest potential in the system and all other
pins must be at higher potential with respect to this pin.
Enable pin. A low signal or left open on this pin shuts down the output. This pin must be tied
HI or to V
An open collector output that switches low when the output voltage drops about 4% below
its expected regulated voltage.
A resistor divider from this pin to the V
PIN DESCRIPTION
IN
and V
IN
for normal operation.
V
V
OUT
V
V
SYM
I
V
Q(SD)
TH(FG)
F(SAT)
EN(L)
EN(L)
IRU1206 / IRU1207 / IRU1208 / IRU1209
HYS
required to main-
Enable=Open
Regulator OFF (Note 4)
Regulator ON (Note 4)
V
V
Output Ramping Up
Io=5mA
Io=500mA
EN(L)
EN(L)
=0V to 0.8V (Note 4)
=2V to Vin (Note 4)
TEST CONDITION
www.irf.com
Note 3: Ground current is the regulator quiescent cur-
rent plus the pass transistor current. The total current
from the supply is the sum of the load current plus the
ground pin current.
Note 4: The specification applies for the junction tem-
perature of 0 to +1258C.
OUT
pin and ground sets the output voltage.
Table 1 - Output voltage vs. part number.
Part Number
IRU1206-18
IRU1206-25
IRU1206-33
IRU1207-18
IRU1207-25
IRU1207-33
IRU1208
IRU1209
MIN
2
TYP
0.01
100
400
230
0.1
0.8
Voltage
Output
5
1.24V
1.24V
1.8V
2.5V
3.3V
1.8V
2.5V
3.3V
MAX
600
0.8
1
2
OUT
UNITS
in order
%V
%V
mV
mA
mA
mA
V
V
O
O
3