24vl024 Microchip Technology Inc., 24vl024 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
24vl024
Manufacturer Part Number
24vl024
Description
2k I 2 C? Serial Eeprom
Manufacturer
Microchip Technology Inc.
Datasheet
1.24VL024.pdf
(30 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
24vl024/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
24vl024H/MS
Manufacturer:
NA
Quantity:
20 000
Part Number:
24vl024H/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
24vl024H/SN
Manufacturer:
MCP
Quantity:
20
Part Number:
24vl024H/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
24vl024H/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
24vl024HT/MNY
Manufacturer:
MCP
Quantity:
20
Company:
Part Number:
24vl024T/MNY
Manufacturer:
MCP
Quantity:
20
Company:
Part Number:
24vl024T/MNY
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
24vl024T/ST
Manufacturer:
MICROCHIP
Quantity:
12 000
6.0
6.1
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits) and the R/W
bit (which is a logic low) are placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24VL024/
24VL025.
signal from the 24VL024/24VL025, the master device
will transmit the data word to be written into the
addressed memory location. The 24VL024/24VL025
acknowledges again and the master generates a Stop
condition. This initiates the internal write cycle and the
24VL024/24VL025 will not generate Acknowledge
signals during this time (Figure 6-1). If an attempt is
made to write to the protected portion of the array when
the hardware write protection has been enabled, the
device will acknowledge the command, but no data will
be written. The write cycle time must be observed even
if write protection is enabled.
6.2
The write-control byte, word address and the first data
byte are transmitted to the 24VL024/24VL025 in the
same way as in a byte write. But instead of generating
a Stop condition, the master transmits up to 15
additional data bytes to the 24VL024/24VL025 that are
temporarily stored in the on-chip page buffer and will be
written into the memory once the master has
transmitted a Stop condition. Upon receipt of each
word, the four lower order Address Pointer bits are
internally incremented by one.
FIGURE 6-1:
FIGURE 6-2:
© 2009 Microchip Technology Inc.
SDA Line
Bus Activity
Master
Bus Activity
SDA Line
Bus Activity
Master
Bus Activity
WRITE OPERATIONS
Byte Write
Page Write
After
S
T
A
R
T
S
receiving
S
S
T
A
R
T
BYTE WRITE
PAGE WRITE
Control
Byte
Control
another
Byte
A
C
K
Acknowledge
Address (n)
Word
A
C
K
A
C
K
Address
Word
Data (n)
The higher order four bits of the word address remain
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2). If an attempt
is made to write to the protected portion of the array
when the hardware write protection has been enabled,
the device will acknowledge the command, but no data
will be written. The write cycle time must be observed
even if write protection is enabled.
6.3
The WP pin must be tied to V
the entire array will be write-protected (00h-FFh). If the
WP pin is tied to V
locations are allowed.
Note:
24VL024/24VL025
Write Protection (24VL024 only)
A
C
K
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page, as might be
expected. It is therefore necessary that the
application software prevent page write
operations that would attempt to cross a
page boundary.
A
C
K
Data (n +1)
SS
, write operations to all address
Data
A
C
K
CC
or V
Data (n + 15)
SS
DS22130A-page 9
. If tied to V
A
C
K
P
S
T
O
P
A
C
K
S
T
O
P
P
CC
,