w83877atd Winbond Electronics Corp America, w83877atd Datasheet - Page 101
w83877atd
Manufacturer Part Number
w83877atd
Description
Winbond I/o
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W83877ATD.pdf
(191 pages)
- Current page: 101 of 191
- Download datasheet (882Kb)
4.3.15 DMA Transfers
DMA transfers are always to or from the ecpDFifo, tFifo, or CFifo. The DMA uses the standard PC
DMA services. The ECP requests DMA transfers from the host by activating the PDRQ pin. The DMA
will empty or fill the FIFO using the appropriate direction and mode. When the terminal count in the
DMA controller is reached, an interrupt is generated and serviceIntr is asserted, which will disable the
DMA.
4.3.16 Programmed I/O (NON-DMA) Mode
The ECP or parallel port FIFOs can also be operated using interrupt driven programmed I/O.
Programmed I/O transfers are to the ecpDFifo at 400H and ecpAFifo at
located at 400H, or to/from the tFifo at 400H. The host must set the direction, state, dmaEn = 0 and
serviceIntr = 0 in the programmed I/O transfers.
The ECP requests programmed I/O transfers from the host by activating the IRQ pin. The
programmed I/O will empty or fill the FIFO using the appropriate direction and mode.
4.4 Extension FDD Mode (EXTFDD)
In this mode, the W83877ATF changes the printer interface pins to FDC input/output pins, allowing
the user to install a second floppy disk drive (FDD B) through the DB-25 printer connector. The pin
assignments for the FDC input/output pins are shown in Table 5-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOB and DSB will be forced to inactive state.
(2) Pins DSKCHG, RDATA , WP, TRAK0, INDEX will be logically ORed with pins PD4-PD0 to
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for
(4) If the parallel port is set to EXTFDD mode after the system has booted DOS or another operating
4.5 Extension 2FDD Mode (EXT2FDD)
In this mode, the W83877ATF changes the printer interface pins to FDC input/output pins, allowing
the user to install two external floppy disk drives through the DB-25 printer connector to replace
internal floppy disk drives A and B. The pin assignments for the FDC input/output pins are shown in
Table 5-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOA , DSA, MOB, and DSB will be forced to inactive state.
(2) Pins DSKCHG, RDATA , WP, TRAK0, and INDEX will be logically ORed with pins PD4-PD0 to
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for
(4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating
serve as input signals to the FDC.
FDD open drain/collector output.
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
serve as input signals to the FDC.
FDD open drain/collector output.
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
- 97 -
Publication Release Date: April 1998
000H,
or from the ecpDFifo
W83877ATF
Version 0.51
Related parts for w83877atd
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Winbond I/O
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 845 Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Via P4/kt Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Pa-risc Embedded Controller
Manufacturer:
Winbond Electronics Corp America
Datasheet: