ad8182-eb Analog Devices, Inc., ad8182-eb Datasheet
ad8182-eb
Related parts for ad8182-eb
ad8182-eb Summary of contents
Page 1
... Switching in LCD and Plasma Displays Video Switchers and Routers PRODUCT DESCRIPTION The AD8180 (single) and AD8182 (dual) are high speed 2-to-1 multiplexers. They offer –3 dB signal bandwidth greater than 750 MHz along with slew rate of 750 V/ s. With better than crosstalk and isolation, they are useful in many high speed applications ...
Page 2
... S –V = –4 –5 All Channels “ON” MIN MAX All Channels “OFF” MIN MAX AD8182, One Channel “ON” –2– unless otherwise noted AD8180A/AD8182A Min Typ Max Units ...
Page 3
... AD8182AR-REEL – +85 C 13" Reel SOIC AD8182AR-REEL7 – +85 C 7" Reel SOIC AD8180-EB Evaluation Board AD8182-EB Evaluation Board MAXIMUM POWER DISSIPATION The maximum power that can be safely dissipated by the AD8180 and AD8182 is limited by the associated rise in junc- tion temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately +150 C ...
Page 4
... AD8180/AD8182–Typical Performance Curves 500mV /DIV 5ns/DIV Figure 4. Channel Switching Characteristics DUT OUT 250mV /DIV 10ns/DIV Figure 5. Enable and Disable Switching Characteristics 50mV /DIV 25ns/DIV Figure 6. Channel Switching Transient (Glitch 50mV rms –1 –2 –3 –4 –5 – ...
Page 5
... AD8182 AD8182R AD8180R 1M 10M 100M FREQUENCY – Hz ALL INPUTS = 0.446V rms 8180R OR OUT A 8182R ENABLE A = LOGIC 1 30 ENABLE B = LOGIC 0 50 OUT AD8182 8182R ENABLE A/B = LOGIC 1 0.1M 1M 10M 100M FREQUENCY – Hz 100 1k 10k 100k 1M 10M 30M FREQUENCY – ...
Page 6
... AD8180/AD8182–Typical Performance Curves – p-p OUT –35 –45 –55 –65 2ND HARMONIC –75 –85 –95 100k 1M 10M FREQUENCY – Hz Figure 16. Harmonic Distortion vs. Frequency 31.6M Z (DISABLED) OUT 3.16M Z (ENABLED) 316k IN 31.6k 3.16k Z (ENABLED) OUT 316 31.6 1k 10k 100k 1M FREQUENCY – Hz Figure 17. Disabled Output and Input Impedance vs. ...
Page 7
... If better flatness response is desired, an input series resistance (R (refer to Figure 20), although this will increase crosstalk. The dc gain of the AD8180 and AD8182 is almost independent of load REV. B for R > For heavier loads, the dc gain is approximately ...
Page 8
... Typically one source would be the PC’s normal output, the second source might be a specialized source such as MPEG video. Figure 23 shows how such a circuit could be realized using the AD8180 and AD8182 and three current feedback op amps. The video inputs to the multiplexers are terminated with 75 resistors ...
Page 9
... AD8182 to create a 4-to-1 multiplexer. The enable control pins on the multiplexers allow the outputs to be wired directly together. Because of its high bandwidth, the AD8182 is capable of driv- ing the switched capacitor input stage of the AD876 without additional buffering. In addition to having the required the bandwidth necessary to consider the settling time of the multiplexer ...
Page 10
... Ordering Guide. Because the footprint of the AD8180 fits directly on to that of the AD8182, one board layout can be used for both devices. In the case of the AD8180, only the top half of the board is populated. Figure 28 shows the silkscreen of the component side and Fig- ure 30 shows the silkscreen of the solder side ...
Page 11
... IN0B J4 Figure 28. Component Side Silkscreen Figure 29. Board Layout (Component Side) NOTES 1. AD8180R/AD8182R Evaluation Board inputs are configured with 50 impedance striplines. This FR4 board type has the following stripline dimensions: 60-mil width, 12-mil gap between center conductor and outside ground plane “is- lands,” ...
Page 12
... AD8180/AD8182 8-Lead Plastic DIP (N-8) 0.430 (10.92) 0.348 (8.84 0.280 (7.11) 0.240 (6.10 0.060 (1.52) PIN 1 0.015 (0.38) 0.210 (5.33) MAX 0.130 (3.30) 0.160 (4.06) MIN 0.115 (2.93) SEATING 0.022 (0.558) 0.100 0.070 (1.77) PLANE (2.54) 0.014 (0.356) 0.045 (1.15) BSC 8-Lead Plastic SOIC (SO-8) 0.1968 (5.00) 0.1890 (4.80 0.1574 (4.00) 0.2440 (6.20 0.1497 (3.80) 0.2284 (5.80) PIN 1 ...