adv7390 Analog Devices, Inc., adv7390 Datasheet - Page 58
![no-image](/images/no-image-200.jpg)
adv7390
Manufacturer Part Number
adv7390
Description
Low Power, Chip Scale 10-bit Sd/hd Video Encoder
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADV7390.pdf
(96 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adv7390BCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adv7390BCPZ-REEL
Manufacturer:
LT
Quantity:
1 000
Company:
Part Number:
adv7390WBCPZ
Manufacturer:
AD
Quantity:
101
ADV7390/ADV7391/ADV7392/ADV7393
Coring Gain Border—Subaddress 0xA3, Bits[3:0]
These four bits are assigned to the gain factor applied to border
areas. In DNR mode, the range of gain values is 0 to 1 in
increments of 1/8. This factor is applied to the DNR filter
output that lies below the set threshold range. The result is then
subtracted from the original signal.
In DNR sharpness mode, the range of gain values is 0 to 0.5 in
increments of 1/16. This factor is applied to the DNR filter
output that lies above the threshold range. The result is added to
the original signal.
Coring Gain Data—Subaddress 0xA3, Bits[7:4]
These four bits are assigned to the gain factor applied to the luma
data inside the MPEG pixel block. In DNR mode, the range of
gain values is 0 to 1 in increments of 1/8. This factor is applied
to the DNR filter output that lies below the set threshold range.
The result is then subtracted from the original signal.
In DNR sharpness mode, the range of gain values is 0 to 0.5 in
increments of 1/16. This factor is applied to the DNR filter
output that lies above the threshold range. The result is added to
the original signal.
DNR27 TO DNR24 = 0x01
DNR Threshold—Subaddress 0xA4, Bits[5:0]
These six bits are used to define the threshold value in the range
of 0 to 63. The range is an absolute value.
Border Area—Subaddress 0xA4, Bit 6
When this bit is set to Logic 1, the block transition area can be
defined to consist of four pixels. If this bit is set to Logic 0, the
border transition area consists of two pixels, where one pixel
refers to two clock cycles at 27 MHz.
720 × 485 PIXELS
(NTSC)
APPLY DATA
CORING GAIN
Figure 80. SD DNR Offset Control
Figure 81. SD DNR Border Area
O X X X X X X O O X X X X X X O
O X X X X X X O O X X X X X X O
O X X X X X X O O X X X X X X O
8 × 8 PIXEL BLOCK
APPLY BORDER
CORING GAIN
BORDER DATA
2-PIXEL
8 × 8 PIXEL BLOCK
OFFSET CAUSED
BY VARIATIONS IN
INPUT TIMING
Rev. 0 | Page 58 of 96
Block Size—Subaddress 0xA4, Bit 7
This bit is used to select the size of the data blocks to be
processed. Setting the block size control function to Logic 1
defines a 16 pixel × 16 pixel data block, and Logic 0 defines an
8 pixel × 8 pixel data block, where one pixel refers to two clock
cycles at 27 MHz.
DNR Input Select—Subaddress 0xA5, Bits[2:0]
These three bits are assigned to select the filter that is applied to
the incoming Y data. The signal that lies in the pass band of the
selected filter is the signal processed by DNR. Figure 82 shows
the filter responses selectable with this control.
DNR Mode—Subaddress 0xA5, Bit 4
This bit controls the DNR mode selected. Logic 0 selects DNR
mode; Logic 1 selects DNR sharpness mode.
DNR works on the principle of defining low amplitude, high
frequency signals as probable noise and subtracting this noise
from the original signal.
In DNR mode, it is possible to subtract a fraction of the signal
that lies below the set threshold, assumed to be noise, from the
original signal. The threshold is set in DNR Register 1.
When DNR sharpness mode is enabled, it is possible to add a
fraction of the signal that lies above the set threshold to the
original signal because this data is assumed to be valid data and
not noise. The overall effect is that the signal is boosted (similar
to using the extended SSAF filter).
Block Offset Control—Subaddress 0xA5, Bits[7:4]
Four bits are assigned to this control that allows a shift in the
data block of 15 pixels maximum. The coring gain positions are
fixed. The block offset shifts the data in steps of one pixel such
that the border coring gain factors can be applied at the same
position regardless of variations in input timing of the data.
1.0
0.8
0.6
0.4
0.2
0
0
FILTER C
FILTER D
1
Figure 82. SD DNR Input Select
2
FREQUENCY (MHz)
FILTER B
3
FILTER A
4
5
6