adv7390 Analog Devices, Inc., adv7390 Datasheet - Page 57
![no-image](/images/no-image-200.jpg)
adv7390
Manufacturer Part Number
adv7390
Description
Low Power, Chip Scale 10-bit Sd/hd Video Encoder
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADV7390.pdf
(96 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adv7390BCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adv7390BCPZ-REEL
Manufacturer:
LT
Quantity:
1 000
Company:
Part Number:
adv7390WBCPZ
Manufacturer:
AD
Quantity:
101
When changing the adaptive filter mode to Mode B
(Subaddress 0x35, Bit 6), the output shown in Figure 78
can be obtained.
SD DIGITAL NOISE REDUCTION
Subaddress 0xA3 to Subaddress 0xA5
Digital noise reduction (DNR) is applied to the Y data only.
A filter block selects the high frequency, low amplitude compo-
nents of the incoming signal (DNR input select). The absolute
value of the filter output is compared to a programmable
threshold value (DNR threshold control). There are two DNR
modes available: DNR mode and DNR sharpness mode.
Figure 77. Output Signal from ED/HD Adaptive Filter (Mode A)
Figure 78. Output Signal from ED/HD Adaptive Filter (Mode B)
Figure 76. Input Signal to ED/HD Adaptive Filter
Rev. 0 | Page 57 of 96
In DNR mode, if the absolute value of the filter output is
smaller than the threshold, it is assumed to be noise. A
programmable amount (coring gain border, coring gain data) of
this noise signal is subtracted from the original signal. In DNR
sharpness mode, if the absolute value of the filter output is less
than the programmed threshold, it is assumed to be noise as
before. However, if the level exceeds the threshold, now being
identified as a valid signal, a fraction of the signal (coring gain
border, coring gain data) is added to the original signal to boost
high frequency components and sharpen the video image.
In MPEG systems, it is common to process the video information
in blocks of 8 pixels × 8 pixels for MPEG2 systems, or 16 pixels
× 16 pixels for MPEG1 systems (block size control). DNR can
be applied to the resulting block transition areas known to
contain noise. Generally, the block transition area contains two
pixels. It is possible to define this area to contain four pixels
(border area).
It is also possible to compensate for variable block positioning
or differences in YCrCb pixel timing with the use of the DNR
block offset.
The digital noise reduction registers are three 8-bit registers.
They are used to control the DNR processing.
Y DATA
Y DATA
INPUT
INPUT
ADV7390/ADV7391/ADV7392/ADV7393
DNR MODE
DNR
SHARPNESS
MODE
NOISE
SIGNAL PATH
NOISE
SIGNAL PATH
INPUT FILTER
INPUT FILTER
MAIN SIGNAL PATH
MAIN SIGNAL PATH
BLOCK
BLOCK
Figure 79. SD DNR Block Diagram
< THRESHOLD?
> THRESHOLD?
BLOCK SIZE CONTROL
CORING GAIN BORDER
BLOCK SIZE CONTROL
CORING GAIN BORDER
OUTPUT
OUTPUT
FILTER
CORING GAIN DATA
FILTER
CORING GAIN DATA
FILTER OUTPUT
< THRESHOLD
BLOCK OFFSET
BLOCK OFFSET
BORDER AREA
FILTER OUTPUT
DNR CONTROL
BORDER AREA
DNR CONTROL
> THRESHOLD
GAIN
GAIN
+
+
–
+
SUBTRACT
SIGNAL IN
THRESHOLD
RANGE FROM
ORIGINAL SIGNAL
ADD SIGNAL
ABOVE
THRESHOLD
RANGE FROM
ORIGINAL SIGNAL
DNR OUT
DNR OUT