ics1893cy-10 Integrated Device Technology, ics1893cy-10 Datasheet - Page 34
ics1893cy-10
Manufacturer Part Number
ics1893cy-10
Description
3.3-v 10base-t/100base-tx Integrated Phyceiver
Manufacturer
Integrated Device Technology
Datasheet
1.ICS1893CY-10.pdf
(143 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ics1893cy-10LF
Manufacturer:
IDT
Quantity:
469
Company:
Part Number:
ics1893cy-10LF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
ics1893cy-10LFT
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
- Current page: 34 of 143
- Download datasheet (2Mb)
5.8 Status Interface
ICS1893CY-10 Rev 1/07
The ICS1893CY-10 LSTA pin provides a Link Status, and its LOCK pin provides a Stream Cipher Locking
Status. In addition, as listed in
that report the results of continual link monitoring by providing signals that are intended for driving LEDs.
(For the pin numbers, see
Table 5-5. Pins for Monitoring the Data Link
Note:
1. During either a power-on reset or a hardware reset, each multi-function configuration pin is an input
2. A software reset does not affect the state of a multi-function configuration pin. During a software reset,
3. Each multi-function configuration pin must be pulled either up or down with a resistor to establish the
4. As outputs, the asserted state of a multi-function configuration pin is the inverse of the sense sampled
5. Adding 10K Ω resistors across the LEDs ensures the PHY address is fully defined during slow VDD
6. PHY address 00 tri-states the MII interface. (Do not select PHY address 00 unless you want the MII
P0AC
P1CL
P2LI
P3TD
P4RD
that is sampled when the ICS1893CY-10 exits the reset state. After sampling is complete, these pins
are output pins that can drive status LEDs.
all multi-function configuration pins are outputs.
address of the ICS1893CY-10. LEDs may be placed in series with these resistors to provide a
designated status indicator as described in Table 5-5.
Caution:
during reset. This inversion provides a signal that can illuminate an LED during an asserted state. For
example, if a multi-function configuration pin is pulled down to ground through an LED and a
current-limiting resistor, then the sampled sense of the input is low. To illuminate this LED for the
asserted state, the output is driven high.
power-ramp conditions.
tri-stated.
Pin
ICS1893CY-10 Data Sheet - Release
AC (Link Activity) LED
CL (Collisions) LED
LI (Link Integrity) LED
TD (Transmit Data) LED
RD (Receive Data) LED
LED Driven by the Pin’s Output Signal
All pins listed in Table 5-5 must not float.
Table
Copyright © 2007, Integrated Device Technology, Inc.
Table
8.3.2.)
5-5, the ICS1893CY-10 provides five multi-function configuration pins
All rights reserved.
34
Chapter 5 Interface Overviews
Related parts for ics1893cy-10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Integrated Processor
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Integrated Riscontroller for Low-Cost Systems
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
INTEGRATED RISController FOR LOW-COST SYSTEMS
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
SwitchStar ATM Cell Based 1.2Gbps non-blocking Integrated Switch Controller
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3V CMOS 16-bit bidirectional transceiver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3 CMOS octal buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal registered transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal bidirectional transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS 16-bit buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5 V/3.3 V 10 Bit High Bandwidth Bus Switch with Precharged Outputs
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
High-Speed CMOS Quick Switch 16:8 Multiplexer
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH?? PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH IDTQS32X245Q2QUICKSWITCH PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5V / 3.3V 16-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet: