UPD78F0138 NEC, UPD78F0138 Datasheet - Page 319
UPD78F0138
Manufacturer Part Number
UPD78F0138
Description
(UPD78xxxx) 8-Bit Single-Chip Microcontrollers
Manufacturer
NEC
Datasheet
1.UPD78F0138.pdf
(558 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD78F0138M1GK-9ET
Manufacturer:
NEC
Quantity:
115
Part Number:
UPD78F0138M5GB
Manufacturer:
NEC
Quantity:
20 000
- Current page: 319 of 558
- Download datasheet (5Mb)
(e) Normal reception
R
X
D6 (input)
Reception is enabled and the R
interface operation mode register 6 (ASIM6) is set to 1 and then bit 5 (RXE6) of ASIM6 is set to 1.
The 8-bit counter of the baud rate generator starts counting when the falling edge of the R
detected. When the set value of baud rate generator control register 6 (BRGC6) has been counted, the
R
as a start bit.
When the start bit is detected, reception is started, and serial data is sequentially stored in the receive shift
register (RXS6) at the set baud rate. When the stop bit has been received, the reception completion interrupt
(INTSR6) is generated and the data of RXS6 is written to receive buffer register 6 (RXB6). If an overrun
error (OVE6) occurs, however, the receive data is not written to RXB6.
Even if a parity error (PE6) occurs while reception is in progress, reception continues to the reception
position of the stop bit, and an error interrupt (INTSR6/INTSRE6) is generated on completion of reception.
Cautions 1. Be sure to read receive buffer register 6 (RXB6) even if a reception error occurs.
INTSR6
X
RXB6
D6 pin input is sampled again (
2. Reception is always performed with the “number of stop bits = 1”. The second stop bit
3. Be sure to read asynchronous serial interface reception error status register 6 (ASIS6)
Otherwise, an overrun error will occur when the next data is received, and the reception
error status will persist.
is ignored.
before reading RXB6.
Figure 14-19. Reception Completion Interrupt Request Timing
Start
D0
CHAPTER 14 SERIAL INTERFACE UART6
D1
X
D6 pin input is sampled when bit 7 (POWER6) of asynchronous serial
in Figure 14-19). If the R
User’s Manual U16228EJ2V0UD
D2
D3
D4
D5
X
D6 pin is low level at this time, it is recognized
D6
D7
Parity
Stop
X
D6 pin input is
319
Related parts for UPD78F0138
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16BIT MCU, 128K FLASH, 8K RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT UC, 32K FLASH, 1KB RAM, LCD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 60K FLASH, 3KB RAM, CAN
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 128K FLASH, 7K RAM, LQFP
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 128B RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet: